Metal weight calculators / Iron combinations
Metal by dimension. Mass by calculation.
Cast Iron Pipe Weight Calculator
Calculate cast iron pipe weight from actual dimensions, density and quantity. Read kg, lb and applicable unit weights, with an optional material-cost estimate.
Your material & dimensions
Your result
Ready to calculateEnter your values and press Calculate. The result will open on the calculation page.
Published references · Clear assumptions · No sign-up
The method
Formula and calculation steps
ID = OD − 2t; A = π(OD² − ID²)/4; mass = density × A × length.
Calculate cast iron pipe weight from actual dimensions, density and quantity. Read kg, lb and applicable unit weights, with an optional material-cost estimate.
- Select a material reference, shape and a consistent dimension unit.
- Confirm metal density, actual dimensions and whether a nominal source preset applies.
- Submit the form, then interpret the result with the assumptions and limits below.
Straight hollow circular section, positive bore required. No fittings, seam allowance, lining, thread loss or coating unless separately stated. All dimensions are nominal or user supplied; use a scale or certified product data for shipping, billing and final procurement.
Cast Iron Pipe: dimensions, density and unit-weight formula
Cast Iron starts at 7200 kg/m³. Rounded from the producer gray-iron example of 0.260 lb/in3. Graphite and grade cause variation; this is not all cast iron. Reference basis: Gray cast iron example, rounded to nearest 100 kg/m3.
Use actual outside diameter and wall thickness. Nominal pipe size is a designation, not a measured outside diameter. Pipe schedules, tube gauge systems and delivered tolerances must be resolved before using dimensional arithmetic.
For cast iron pipe weight, keep a single physical piece definition: separate lengths, product counts and voids before multiplying. Convert dimensions consistently; millimetre volume scales by 10⁻⁹ to m³, while cubic inches use 0.0254³. Nominal designation and measured dimension are different inputs. Verify the drawing or product specification before interpreting a calculated total.
Continue with: Cast Iron Plate Weight Calculator · Ductile Iron Pipe Weight Calculator · Iron Angle Weight Calculator · Iron Flat Bar Weight Calculator
Check the numbers
Cast Iron Pipe Weight Calculator: calculated examples
These results are calculated from the dimensions or published-mass records stated in each row. They are not a complete inventory, certified tolerance table or structural design.
Worked example with stated inputs
Material density reference = Cast Iron; Shape = Pipe; Dimension units = Millimetres (mm); Density (editable override) = 7200 kg/m³; Outside / solid diameter = 50 mm; Wall thickness = 3 mm; Piece / sidewall length = 1000 mm; Quantity = 1 pieces; Optional unit price (0 = omit) = 0 ; Price basis = Price per kg; Cost currency label = USD.
| Output | Computed result |
|---|---|
| Single-piece calculated mass | 3.189345 kg |
| Single-piece mass | 7.031302 lb |
| Quantity | 1 pieces |
| Total mass | 3.189345 kg |
| Total mass in pounds | 7.031302 lb |
| Linear mass | 3.189345 kg/m |
| Linear mass in imperial units | 2.143141 lb/ft |
| Net model metal volume | 0.000443 m³ |
| Selected shape | Pipe |
| Material reference | Cast Iron |
| Density entered | 7,200 kg/m³ |
| Calculation basis | Geometry × supplied density |
Dimensioned weight examples in kg
| Scenario | Dimension set / calculation basis | Result |
|---|---|---|
| 500 mm | Piece / sidewall length | 1.594672 kg |
| 750 mm | Piece / sidewall length | 2.392009 kg |
| 1000 mm | Piece / sidewall length | 3.189345 kg |
| 1500 mm | Piece / sidewall length | 4.784017 kg |
| 2000 mm | Piece / sidewall length | 6.37869 kg |
| 3000 mm | Piece / sidewall length | 9.568035 kg |
Unchanged inputs use: Material density reference = Cast Iron; Shape = Pipe; Dimension units = Millimetres (mm); Density (editable override) = 7200 kg/m³; Outside / solid diameter = 50 mm; Wall thickness = 3 mm; Piece / sidewall length = 1000 mm; Quantity = 1 pieces; Optional unit price (0 = omit) = 0 ; Price basis = Price per kg; Cost currency label = USD. Results retain the model limitations described above.
Common questions
What density does this material weight calculator use?
Cast Iron starts at 7200 kg/m³. Rounded from the producer gray-iron example of 0.260 lb/in3. Graphite and grade cause variation; this is not all cast iron. Reference basis: Gray cast iron example, rounded to nearest 100 kg/m3.
What is the cast iron pipe weight calculation formula?
ID = OD − 2t; A = π(OD² − ID²)/4; mass = density × A × length. The initial density is 7200 kg/m³ for Gray cast iron example, rounded to nearest 100 kg/m3. The dimensioned examples on this page show the resulting piece mass; quantity and optional unit price are applied separately.
How do I calculate weight in kg and lbs?
The dimensional model gives metal volume in m³, multiplied by the entered kg/m³ density. One avoirdupois pound is exactly 0.45359237 kg. The result reports kg and lb; these are mass units, while force weight would require a gravitational acceleration.
Can I get weight per meter and per foot?
Uniform bars, pipes and section-area models report kg/m and lb/ft. One foot is exactly 0.3048 m. Area and nonuniform objects instead use their stated geometry; a sphere or coil does not have a meaningful generic straight-stock kg/m.
Can I enter NPS or DN as outside diameter?
No. Use the dimensional standard or supplier drawing to find actual OD. The schedule table tool supplies a few explicitly sourced pipe examples.
Is wall thickness equal to a schedule number?
No. Schedule 10S or 40S is a series whose wall depends on nominal size. Enter the actual decimal thickness, or use a sourced preset.
Can I export this calculation to Excel?
Calculate first, then choose Export CSV. The CSV contains the submitted model and inputs plus piece mass, total mass and applicable unit weights. Excel can open this text format; it is not a downloadable formula workbook or desktop application.
Does optional price include shipping or fabrication?
No. Enter a price per kg or per lb in the chosen currency label. The total is material mass times that unit price only, with no exchange-rate lookup, tax, minimum order, cutting loss or fabrication labor.
How should I read the calculated tables?
Each table states its geometry, material density and assumptions. Example dimensions are calculation scenarios unless explicitly identified as sourced nominal presets. They are not an inventory list or tolerance guarantee.
Related calculators
Formula sources and references
References support the underlying methods and units. Chosen example inputs are not universal recommendations, certified tolerances or proprietary performance ratings.
- OpenStax College Physics 2e, 11.2 Density: mass, volume and density relationshiphttps://openstax.org/books/college-physics-2e/pages/11-2-density
- NIST SP 811, Appendix B.9: mass, length and derived-unit conversionshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors/nist-guide-si-appendix-b9
- Dura-Bar Density technical brief, gray-iron example 0.260 lb/in3https://dura-bar.com/getmedia/811341e6-6541-48f9-b719-1d1d666a2bc8/dura-bar-density-0219.pdf?ext=.pdf