Metal weight calculators / Materials
Metal by dimension. Mass by calculation.
D2 Tool Steel Weight Calculator
Calculate d2 tool steel weight from actual dimensions, density and quantity. Read kg, lb and applicable unit weights, with an optional material-cost estimate.
Your material & dimensions
Your result
Ready to calculateEnter your values and press Calculate. The result will open on the calculation page.
Published references · Clear assumptions · No sign-up
The method
Formula and calculation steps
Mass = density × net metal volume. For a uniform prism V = section area × length; hollow sections subtract the bore; coils and spheres use their specific geometry.
Calculate d2 tool steel weight from actual dimensions, density and quantity. Read kg, lb and applicable unit weights, with an optional material-cost estimate.
- Select a material reference, shape and a consistent dimension unit.
- Confirm metal density, actual dimensions and whether a nominal source preset applies.
- Submit the form, then interpret the result with the assumptions and limits below.
Use the selected shape’s dimensional model and assumptions. Preset densities are source-scoped estimates; coatings, finished-product tolerances and procurement allowances require separate verification.
D2 Tool Steel density, shapes and calculation units
D2 Tool Steel starts at 7700 kg/m³. Uddeholm Sverker 21 physical data at 20 C for material hardened and tempered to 62 HRC. Reference basis: AISI D2 / Sverker 21, 20 C.
Choose a shape to reveal its dimensions. Plates use width, thickness and length; round stock uses circular area; pipes subtract the circular bore; rolled profiles need published material area or nominal mass when fillets and tapered flanges matter. A positive geometric result is not a structural capacity calculation.
For d2 tool steel weight, keep a single physical piece definition: separate lengths, product counts and voids before multiplying. Convert dimensions consistently; millimetre volume scales by 10⁻⁹ to m³, while cubic inches use 0.0254³. Nominal designation and measured dimension are different inputs. Verify the drawing or product specification before interpreting a calculated total.
Continue with: A2 Tool Steel Weight Calculator · A36 Steel Weight Calculator · Alloy Steel Weight Calculator · Aluminum Weight Calculator
Check the numbers
D2 Tool Steel Weight Calculator: calculated examples
These results are calculated from the dimensions or published-mass records stated in each row. They are not a complete inventory, certified tolerance table or structural design.
Worked example with stated inputs
Material density reference = D2 Tool Steel; Shape = Plate; Dimension units = Millimetres (mm); Density (editable override) = 7700 kg/m³; Width = 1000 mm; Base / wall thickness = 6 mm; Piece / sidewall length = 1000 mm; Quantity = 1 pieces; Optional unit price (0 = omit) = 0 ; Price basis = Price per kg; Cost currency label = USD.
| Output | Computed result |
|---|---|
| Single-piece calculated mass | 46.2 kg |
| Single-piece mass | 101.853565 lb |
| Quantity | 1 pieces |
| Total mass | 46.2 kg |
| Total mass in pounds | 101.853565 lb |
| Linear mass | 46.2 kg/m |
| Linear mass in imperial units | 31.044967 lb/ft |
| Projected area mass | 46.2 kg/m² |
| Projected area mass in imperial units | 9.462506 lb/ft² |
| Net model metal volume | 0.006 m³ |
| Selected shape | Plate |
| Material reference | D2 Tool Steel |
| Density entered | 7,700 kg/m³ |
| Calculation basis | Geometry × supplied density |
Dimensioned weight examples in kg
| Scenario | Dimension set / calculation basis | Result |
|---|---|---|
| Plate | Width 1000 mm, Base / wall thickness 6 mm, Piece / sidewall length 1000 mm | 46.2 kg |
| Round Bar | Outside / solid diameter 50 mm, Piece / sidewall length 1000 mm | 15.118915 kg |
| Pipe | Outside / solid diameter 50 mm, Wall thickness 3 mm, Piece / sidewall length 1000 mm | 3.410827 kg |
| Square Bar | Overall width / first side 50 mm, Piece / sidewall length 1000 mm | 19.25 kg |
| Angle | First leg outside size 75 mm, Second leg outside size 75 mm, Uniform leg thickness 6 mm, Piece / sidewall length 1000 mm | 6.6528 kg |
| Sphere | Outside / solid diameter 50 mm | 0.503964 kg |
Unchanged inputs use: Material density reference = D2 Tool Steel; Shape = Plate; Dimension units = Millimetres (mm); Density (editable override) = 7700 kg/m³; Width = 1000 mm; Base / wall thickness = 6 mm; Piece / sidewall length = 1000 mm; Quantity = 1 pieces; Optional unit price (0 = omit) = 0 ; Price basis = Price per kg; Cost currency label = USD. Results retain the model limitations described above.
Common questions
What density does this material weight calculator use?
D2 Tool Steel starts at 7700 kg/m³. Uddeholm Sverker 21 physical data at 20 C for material hardened and tempered to 62 HRC. Reference basis: AISI D2 / Sverker 21, 20 C.
What is the d2 tool steel weight calculation formula?
Mass = density × net metal volume. For a uniform prism V = section area × length; hollow sections subtract the bore; coils and spheres use their specific geometry. The initial density is 7700 kg/m³ for AISI D2 / Sverker 21, 20 C. The dimensioned examples on this page show the resulting piece mass; quantity and optional unit price are applied separately.
How do I calculate weight in kg and lbs?
The dimensional model gives metal volume in m³, multiplied by the entered kg/m³ density. One avoirdupois pound is exactly 0.45359237 kg. The result reports kg and lb; these are mass units, while force weight would require a gravitational acceleration.
Can I get weight per meter and per foot?
Uniform bars, pipes and section-area models report kg/m and lb/ft. One foot is exactly 0.3048 m. Area and nonuniform objects instead use their stated geometry; a sphere or coil does not have a meaningful generic straight-stock kg/m.
Can I use a sheet gauge instead of thickness?
Enter its verified decimal thickness. Steel, galvanized, stainless and nonferrous gauge systems differ; a bare gauge number has no universal millimetre equivalent.
Is this the delivered or theoretical weight?
It is theoretical mass from stated nominal or measured dimensions. Mill tolerances and order packaging can change the scale reading.
Can I export this calculation to Excel?
Calculate first, then choose Export CSV. The CSV contains the submitted model and inputs plus piece mass, total mass and applicable unit weights. Excel can open this text format; it is not a downloadable formula workbook or desktop application.
Does optional price include shipping or fabrication?
No. Enter a price per kg or per lb in the chosen currency label. The total is material mass times that unit price only, with no exchange-rate lookup, tax, minimum order, cutting loss or fabrication labor.
How should I read the calculated tables?
Each table states its geometry, material density and assumptions. Example dimensions are calculation scenarios unless explicitly identified as sourced nominal presets. They are not an inventory list or tolerance guarantee.
Related calculators
Formula sources and references
References support the underlying methods and units. Chosen example inputs are not universal recommendations, certified tolerances or proprietary performance ratings.
- OpenStax College Physics 2e, 11.2 Density: mass, volume and density relationshiphttps://openstax.org/books/college-physics-2e/pages/11-2-density
- NIST SP 811, Appendix B.9: mass, length and derived-unit conversionshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors/nist-guide-si-appendix-b9
- Uddeholm Sverker 21: AISI D2 physical data at 20 Chttps://www.voestalpine.com/highperformancemetals/denmark/app/uploads/sites/249/productdb/api/tech_uddeholm-sverker-21_en.pdf