Metal Weight CalculatorMaterials, shapes & unit weights

Metal weight calculators / Materials

Metal by dimension. Mass by calculation.

Gunmetal Weight Calculator

Calculate gunmetal weight from actual dimensions, density and quantity. Read kg, lb and applicable unit weights, with an optional material-cost estimate.

Your material & dimensions

kg/m³
mm
mm
mm
mm
mm
mm
mm
mm
mm
mm
mm
holes
mm
ratio
ends
mm
mm
ratio
kg/m²
kg/m²
mm²
mm³
pieces

Preset densities are editable reference estimates. Dimensions use the selected mm/in unit. Published kg/m presets use their source mass directly; choose Custom dimensions to edit their geometry. Initial inputs are examples.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

Mass = density × net metal volume. For a uniform prism V = section area × length; hollow sections subtract the bore; coils and spheres use their specific geometry.

Calculate gunmetal weight from actual dimensions, density and quantity. Read kg, lb and applicable unit weights, with an optional material-cost estimate.

  1. Select a material reference, shape and a consistent dimension unit.
  2. Confirm metal density, actual dimensions and whether a nominal source preset applies.
  3. Submit the form, then interpret the result with the assumptions and limits below.

Use the selected shape’s dimensional model and assumptions. Preset densities are source-scoped estimates; coatings, finished-product tolerances and procurement allowances require separate verification.

Gunmetal density, shapes and calculation units

Gunmetal starts at 8720 kg/m³. Uses C90500 tin bronze as a declared gunmetal example. Gunmetal is a trade family, not one universal composition. Reference basis: UNS C90500 representative.

Choose a shape to reveal its dimensions. Plates use width, thickness and length; round stock uses circular area; pipes subtract the circular bore; rolled profiles need published material area or nominal mass when fillets and tapered flanges matter. A positive geometric result is not a structural capacity calculation.

For gunmetal weight, keep a single physical piece definition: separate lengths, product counts and voids before multiplying. Convert dimensions consistently; millimetre volume scales by 10⁻⁹ to m³, while cubic inches use 0.0254³. Nominal designation and measured dimension are different inputs. Verify the drawing or product specification before interpreting a calculated total.

Check the numbers

Gunmetal Weight Calculator: calculated examples

These results are calculated from the dimensions or published-mass records stated in each row. They are not a complete inventory, certified tolerance table or structural design.

Worked example with stated inputs

Material density reference = Gunmetal; Shape = Plate; Dimension units = Millimetres (mm); Density (editable override) = 8720 kg/m³; Width = 1000 mm; Base / wall thickness = 6 mm; Piece / sidewall length = 1000 mm; Quantity = 1 pieces; Optional unit price (0 = omit) = 0 ; Price basis = Price per kg; Cost currency label = USD.

OutputComputed result
Single-piece calculated mass52.32 kg
Single-piece mass115.345856 lb
Quantity1 pieces
Total mass52.32 kg
Total mass in pounds115.345856 lb
Linear mass52.32 kg/m
Linear mass in imperial units35.157417 lb/ft
Projected area mass52.32 kg/m²
Projected area mass in imperial units10.715981 lb/ft²
Net model metal volume0.006 m³
Selected shapePlate
Material referenceGunmetal
Density entered8,720 kg/m³
Calculation basisGeometry × supplied density

Dimensioned weight examples in kg

ScenarioDimension set / calculation basisResult
PlateWidth 1000 mm, Base / wall thickness 6 mm, Piece / sidewall length 1000 mm52.32 kg
Round BarOutside / solid diameter 50 mm, Piece / sidewall length 1000 mm17.12168 kg
PipeOutside / solid diameter 50 mm, Wall thickness 3 mm, Piece / sidewall length 1000 mm3.862651 kg
Square BarOverall width / first side 50 mm, Piece / sidewall length 1000 mm21.8 kg
AngleFirst leg outside size 75 mm, Second leg outside size 75 mm, Uniform leg thickness 6 mm, Piece / sidewall length 1000 mm7.53408 kg
SphereOutside / solid diameter 50 mm0.570723 kg

Unchanged inputs use: Material density reference = Gunmetal; Shape = Plate; Dimension units = Millimetres (mm); Density (editable override) = 8720 kg/m³; Width = 1000 mm; Base / wall thickness = 6 mm; Piece / sidewall length = 1000 mm; Quantity = 1 pieces; Optional unit price (0 = omit) = 0 ; Price basis = Price per kg; Cost currency label = USD. Results retain the model limitations described above.

Common questions

What density does this material weight calculator use?

Gunmetal starts at 8720 kg/m³. Uses C90500 tin bronze as a declared gunmetal example. Gunmetal is a trade family, not one universal composition. Reference basis: UNS C90500 representative.

What is the gunmetal weight calculation formula?

Mass = density × net metal volume. For a uniform prism V = section area × length; hollow sections subtract the bore; coils and spheres use their specific geometry. The initial density is 8720 kg/m³ for UNS C90500 representative. The dimensioned examples on this page show the resulting piece mass; quantity and optional unit price are applied separately.

How do I calculate weight in kg and lbs?

The dimensional model gives metal volume in m³, multiplied by the entered kg/m³ density. One avoirdupois pound is exactly 0.45359237 kg. The result reports kg and lb; these are mass units, while force weight would require a gravitational acceleration.

Can I get weight per meter and per foot?

Uniform bars, pipes and section-area models report kg/m and lb/ft. One foot is exactly 0.3048 m. Area and nonuniform objects instead use their stated geometry; a sphere or coil does not have a meaningful generic straight-stock kg/m.

Can I use a sheet gauge instead of thickness?

Enter its verified decimal thickness. Steel, galvanized, stainless and nonferrous gauge systems differ; a bare gauge number has no universal millimetre equivalent.

Is this the delivered or theoretical weight?

It is theoretical mass from stated nominal or measured dimensions. Mill tolerances and order packaging can change the scale reading.

Can I export this calculation to Excel?

Calculate first, then choose Export CSV. The CSV contains the submitted model and inputs plus piece mass, total mass and applicable unit weights. Excel can open this text format; it is not a downloadable formula workbook or desktop application.

Does optional price include shipping or fabrication?

No. Enter a price per kg or per lb in the chosen currency label. The total is material mass times that unit price only, with no exchange-rate lookup, tax, minimum order, cutting loss or fabrication labor.

How should I read the calculated tables?

Each table states its geometry, material density and assumptions. Example dimensions are calculation scenarios unless explicitly identified as sourced nominal presets. They are not an inventory list or tolerance guarantee.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, certified tolerances or proprietary performance ratings.

  • OpenStax College Physics 2e, 11.2 Density: mass, volume and density relationshiphttps://openstax.org/books/college-physics-2e/pages/11-2-density
  • NIST SP 811, Appendix B.9: mass, length and derived-unit conversionshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors/nist-guide-si-appendix-b9
  • Copper Development Association: cast copper alloy sleeve bearings, density tablehttps://www.copper.org/publications/pub_list/pdf/sleevebearing_a1063_06.pdf