Metal Weight CalculatorMaterials, shapes & unit weights

Metal weight calculators / Stainless steel combinations

Metal by dimension. Mass by calculation.

SS 304 Pipe Weight Calculator

Calculate ss 304 pipe weight from actual dimensions, density and quantity. Read kg, lb and applicable unit weights, with an optional material-cost estimate.

Your material & dimensions

kg/m³
mm
mm
mm
pieces

Preset densities are editable reference estimates. Dimensions use the selected mm/in unit. Published kg/m presets use their source mass directly; choose Custom dimensions to edit their geometry. Initial inputs are examples.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

ID = OD − 2t; A = π(OD² − ID²)/4; mass = density × A × length.

Calculate ss 304 pipe weight from actual dimensions, density and quantity. Read kg, lb and applicable unit weights, with an optional material-cost estimate.

  1. Select a material reference, shape and a consistent dimension unit.
  2. Confirm metal density, actual dimensions and whether a nominal source preset applies.
  3. Submit the form, then interpret the result with the assumptions and limits below.

Straight hollow circular section, positive bore required. No fittings, seam allowance, lining, thread loss or coating unless separately stated. All dimensions are nominal or user supplied; use a scale or certified product data for shipping, billing and final procurement.

SS 304 Pipe: dimensions, density and unit-weight formula

SS 304 starts at 7900 kg/m³. Room-temperature reference for 304 / EN 1.4301. Density does not establish corrosion or strength suitability. Reference basis: AISI 304 / EN 1.4301, 20 C.

Use actual outside diameter and wall thickness. Nominal pipe size is a designation, not a measured outside diameter. Pipe schedules, tube gauge systems and delivered tolerances must be resolved before using dimensional arithmetic.

For ss 304 pipe weight, keep a single physical piece definition: separate lengths, product counts and voids before multiplying. Convert dimensions consistently; millimetre volume scales by 10⁻⁹ to m³, while cubic inches use 0.0254³. Nominal designation and measured dimension are different inputs. Verify the drawing or product specification before interpreting a calculated total.

Check the numbers

SS 304 Pipe Weight Calculator: calculated examples

These results are calculated from the dimensions or published-mass records stated in each row. They are not a complete inventory, certified tolerance table or structural design.

Worked example with stated inputs

Material density reference = SS 304; Shape = Pipe; Dimension units = Millimetres (mm); Density (editable override) = 7900 kg/m³; Dimension / published-mass preset = Custom dimensions; Outside / solid diameter = 21.336 mm; Wall thickness = 2.1082 mm; Piece / sidewall length = 1000 mm; Quantity = 1 pieces; Optional unit price (0 = omit) = 0 ; Price basis = Price per kg; Cost currency label = USD.

OutputComputed result
Single-piece calculated mass1.006047 kg
Single-piece mass2.217954 lb
Quantity1 pieces
Total mass1.006047 kg
Total mass in pounds2.217954 lb
Linear mass1.006047 kg/m
Linear mass in imperial units0.676033 lb/ft
Net model metal volume0.000127 m³
Selected shapePipe
Material referenceSS 304
Density entered7,900 kg/m³
Calculation basisGeometry × supplied density

Dimensioned weight examples in kg

ScenarioDimension set / calculation basisResult
NPS 1/2 Sch 10Sdiameter 21.336 mm, thickness 2.1082 mm1.006047 kg
NPS 1/2 Sch 40Sdiameter 21.336 mm, thickness 2.7686 mm1.275817 kg
NPS 3/4 Sch 10Sdiameter 26.67 mm, thickness 2.1082 mm1.285136 kg
NPS 3/4 Sch 40Sdiameter 26.67 mm, thickness 2.8702 mm1.695362 kg
NPS 1 Sch 10Sdiameter 33.401 mm, thickness 2.7686 mm2.104836 kg
NPS 1 Sch 40Sdiameter 33.401 mm, thickness 3.3782 mm2.517176 kg
NPS 2 Sch 10Sdiameter 60.325 mm, thickness 2.7686 mm3.954857 kg
NPS 2 Sch 40Sdiameter 60.325 mm, thickness 3.9116 mm5.476633 kg

Unchanged inputs use: Material density reference = SS 304; Shape = Pipe; Dimension units = Millimetres (mm); Density (editable override) = 7900 kg/m³; Dimension / published-mass preset = Custom dimensions; Outside / solid diameter = 21.336 mm; Wall thickness = 2.1082 mm; Piece / sidewall length = 1000 mm; Quantity = 1 pieces; Optional unit price (0 = omit) = 0 ; Price basis = Price per kg; Cost currency label = USD. Results retain the model limitations described above.

Common questions

What density does this material weight calculator use?

SS 304 starts at 7900 kg/m³. Room-temperature reference for 304 / EN 1.4301. Density does not establish corrosion or strength suitability. Reference basis: AISI 304 / EN 1.4301, 20 C.

What is the ss 304 pipe weight calculation formula?

ID = OD − 2t; A = π(OD² − ID²)/4; mass = density × A × length. The initial density is 7900 kg/m³ for AISI 304 / EN 1.4301, 20 C. The dimensioned examples on this page show the resulting piece mass; quantity and optional unit price are applied separately.

How do I calculate weight in kg and lbs?

The dimensional model gives metal volume in m³, multiplied by the entered kg/m³ density. One avoirdupois pound is exactly 0.45359237 kg. The result reports kg and lb; these are mass units, while force weight would require a gravitational acceleration.

Can I get weight per meter and per foot?

Uniform bars, pipes and section-area models report kg/m and lb/ft. One foot is exactly 0.3048 m. Area and nonuniform objects instead use their stated geometry; a sphere or coil does not have a meaningful generic straight-stock kg/m.

Can I enter NPS or DN as outside diameter?

No. Use the dimensional standard or supplier drawing to find actual OD. The schedule table tool supplies a few explicitly sourced pipe examples.

How are the sourced size presets different from custom geometry?

A dimensional preset supplies published nominal OD and wall. A published-mass preset uses its source kg/m directly and ignores density for that mass. Select Custom dimensions for the simple geometric estimate. These two bases can differ because of fillets, manufacturing conventions and catalogue rounding.

Is wall thickness equal to a schedule number?

No. Schedule 10S or 40S is a series whose wall depends on nominal size. Enter the actual decimal thickness, or use a sourced preset.

Can I export this calculation to Excel?

Calculate first, then choose Export CSV. The CSV contains the submitted model and inputs plus piece mass, total mass and applicable unit weights. Excel can open this text format; it is not a downloadable formula workbook or desktop application.

Does optional price include shipping or fabrication?

No. Enter a price per kg or per lb in the chosen currency label. The total is material mass times that unit price only, with no exchange-rate lookup, tax, minimum order, cutting loss or fabrication labor.

How should I read the calculated tables?

Each table states its geometry, material density and assumptions. Example dimensions are calculation scenarios unless explicitly identified as sourced nominal presets. They are not an inventory list or tolerance guarantee.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, certified tolerances or proprietary performance ratings.

  • OpenStax College Physics 2e, 11.2 Density: mass, volume and density relationshiphttps://openstax.org/books/college-physics-2e/pages/11-2-density
  • NIST SP 811, Appendix B.9: mass, length and derived-unit conversionshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors/nist-guide-si-appendix-b9
  • Euro Inox: Stainless Steel Tables of Technical Properties, 2007, physical properties pp. 16-17https://worldstainless.org/wp-content/uploads/2025/02/Tables_TechnicalProperties_EN.pdf
  • Penn Stainless Products: Pipe Dimensions, nominal OD and wall in inches; NPS 1/2, 3/4, 1 and 2, Schedule 10S and 40S rowshttps://www.pennstainless.com/resources/product-resources/pipe-dimensions/
  • ASME B36.19-2022: Welded and Seamless Wrought Stainless Steel Pipe; Publisher cover and table of contentshttps://www.asme.org/getmedia/a9eaf44a-2fd2-4063-a6e5-c648750bf781/table-of-contents_b36-19-2022.pdf