Metal weight calculators / Stainless steel combinations
Metal by dimension. Mass by calculation.
SS 304 Rectangular Tube Weight Calculator
Calculate ss 304 rectangular tube weight from actual dimensions, density and quantity. Read kg, lb and applicable unit weights, with an optional material-cost estimate.
Your material & dimensions
Your result
Ready to calculateEnter your values and press Calculate. The result will open on the calculation page.
Published references · Clear assumptions · No sign-up
The method
Formula and calculation steps
A = B×H − (B−2t)(H−2t); for SHS set H=B; mass = density × A × length.
Calculate ss 304 rectangular tube weight from actual dimensions, density and quantity. Read kg, lb and applicable unit weights, with an optional material-cost estimate.
- Select a material reference, shape and a consistent dimension unit.
- Confirm metal density, actual dimensions and whether a nominal source preset applies.
- Submit the form, then interpret the result with the assumptions and limits below.
Sharp-corner approximation, not an EN/ASTM hollow-section certified mass. All dimensions are nominal or user supplied; use a scale or certified product data for shipping, billing and final procurement.
SS 304 Rectangular Hollow Section (RHS): dimensions, density and unit-weight formula
SS 304 starts at 7900 kg/m³. Room-temperature reference for 304 / EN 1.4301. Density does not establish corrosion or strength suitability. Reference basis: AISI 304 / EN 1.4301, 20 C.
Subtract the inner rectangular opening from the outer rectangle. This transparent estimate uses sharp corners and uniform thickness. Real cold-formed hollow sections have rounded corners, so a supplier certified section area is preferable for an exact catalogue estimate.
For ss 304 rectangular tube weight, keep a single physical piece definition: separate lengths, product counts and voids before multiplying. Convert dimensions consistently; millimetre volume scales by 10⁻⁹ to m³, while cubic inches use 0.0254³. Nominal designation and measured dimension are different inputs. Verify the drawing or product specification before interpreting a calculated total.
Continue with: SS 202 Sheet Weight Calculator · SS 304 Angle Weight Calculator · SS 304 Channel Weight Calculator · SS 304 Checker Plate Weight Calculator
Check the numbers
SS 304 Rectangular Tube Weight Calculator: calculated examples
These results are calculated from the dimensions or published-mass records stated in each row. They are not a complete inventory, certified tolerance table or structural design.
Worked example with stated inputs
Material density reference = SS 304; Shape = Rectangular Hollow Section (RHS); Dimension units = Millimetres (mm); Density (editable override) = 7900 kg/m³; Overall width / first side = 50 mm; Overall height / second side = 100 mm; Wall thickness = 3 mm; Piece / sidewall length = 1000 mm; Quantity = 1 pieces; Optional unit price (0 = omit) = 0 ; Price basis = Price per kg; Cost currency label = USD.
| Output | Computed result |
|---|---|
| Single-piece calculated mass | 6.8256 kg |
| Single-piece mass | 15.047872 lb |
| Quantity | 1 pieces |
| Total mass | 6.8256 kg |
| Total mass in pounds | 15.047872 lb |
| Linear mass | 6.8256 kg/m |
| Linear mass in imperial units | 4.586591 lb/ft |
| Net model metal volume | 0.000864 m³ |
| Selected shape | Rectangular Hollow Section (RHS) |
| Material reference | SS 304 |
| Density entered | 7,900 kg/m³ |
| Calculation basis | Geometry × supplied density |
Dimensioned weight examples in kg
| Scenario | Dimension set / calculation basis | Result |
|---|---|---|
| 500 mm | Piece / sidewall length | 3.4128 kg |
| 750 mm | Piece / sidewall length | 5.1192 kg |
| 1000 mm | Piece / sidewall length | 6.8256 kg |
| 1500 mm | Piece / sidewall length | 10.2384 kg |
| 2000 mm | Piece / sidewall length | 13.6512 kg |
| 3000 mm | Piece / sidewall length | 20.4768 kg |
Unchanged inputs use: Material density reference = SS 304; Shape = Rectangular Hollow Section (RHS); Dimension units = Millimetres (mm); Density (editable override) = 7900 kg/m³; Overall width / first side = 50 mm; Overall height / second side = 100 mm; Wall thickness = 3 mm; Piece / sidewall length = 1000 mm; Quantity = 1 pieces; Optional unit price (0 = omit) = 0 ; Price basis = Price per kg; Cost currency label = USD. Results retain the model limitations described above.
Common questions
What density does this material weight calculator use?
SS 304 starts at 7900 kg/m³. Room-temperature reference for 304 / EN 1.4301. Density does not establish corrosion or strength suitability. Reference basis: AISI 304 / EN 1.4301, 20 C.
What is the ss 304 rectangular tube weight calculation formula?
A = B×H − (B−2t)(H−2t); for SHS set H=B; mass = density × A × length. The initial density is 7900 kg/m³ for AISI 304 / EN 1.4301, 20 C. The dimensioned examples on this page show the resulting piece mass; quantity and optional unit price are applied separately.
How do I calculate weight in kg and lbs?
The dimensional model gives metal volume in m³, multiplied by the entered kg/m³ density. One avoirdupois pound is exactly 0.45359237 kg. The result reports kg and lb; these are mass units, while force weight would require a gravitational acceleration.
Can I get weight per meter and per foot?
Uniform bars, pipes and section-area models report kg/m and lb/ft. One foot is exactly 0.3048 m. Area and nonuniform objects instead use their stated geometry; a sphere or coil does not have a meaningful generic straight-stock kg/m.
Does this account for rounded hollow-section corners?
No. Enter the published area in the section-area calculator when corner radii and production details matter.
Can the wall equal half the smaller outside side?
No. That would remove the bore and is rejected. Use a solid bar calculator for a solid section.
Can I export this calculation to Excel?
Calculate first, then choose Export CSV. The CSV contains the submitted model and inputs plus piece mass, total mass and applicable unit weights. Excel can open this text format; it is not a downloadable formula workbook or desktop application.
Does optional price include shipping or fabrication?
No. Enter a price per kg or per lb in the chosen currency label. The total is material mass times that unit price only, with no exchange-rate lookup, tax, minimum order, cutting loss or fabrication labor.
How should I read the calculated tables?
Each table states its geometry, material density and assumptions. Example dimensions are calculation scenarios unless explicitly identified as sourced nominal presets. They are not an inventory list or tolerance guarantee.
Related calculators
Formula sources and references
References support the underlying methods and units. Chosen example inputs are not universal recommendations, certified tolerances or proprietary performance ratings.
- OpenStax College Physics 2e, 11.2 Density: mass, volume and density relationshiphttps://openstax.org/books/college-physics-2e/pages/11-2-density
- NIST SP 811, Appendix B.9: mass, length and derived-unit conversionshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors/nist-guide-si-appendix-b9
- Euro Inox: Stainless Steel Tables of Technical Properties, 2007, physical properties pp. 16-17https://worldstainless.org/wp-content/uploads/2025/02/Tables_TechnicalProperties_EN.pdf