Metal Weight CalculatorMaterials, shapes & unit weights

Metal weight calculators / Stainless steel combinations

Metal by dimension. Mass by calculation.

Stainless Steel Coil Weight Calculator

Calculate stainless steel coil weight from actual dimensions, density and quantity. Read kg, lb and applicable unit weights, with an optional material-cost estimate.

Your material & dimensions

kg/m³
mm
mm
mm
ratio
pieces

Preset densities are editable reference estimates. Dimensions use the selected mm/in unit. Published kg/m presets use their source mass directly; choose Custom dimensions to edit their geometry. Initial inputs are examples.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

Vmetal = π(OD²−ID²) × coil width × packing fraction /4; mass = density × Vmetal.

Calculate stainless steel coil weight from actual dimensions, density and quantity. Read kg, lb and applicable unit weights, with an optional material-cost estimate.

  1. Select a material reference, shape and a consistent dimension unit.
  2. Confirm metal density, actual dimensions and whether a nominal source preset applies.
  3. Submit the form, then interpret the result with the assumptions and limits below.

Annular-envelope estimate only. Core, wrapping, straps, oil and packaging are excluded. All dimensions are nominal or user supplied; use a scale or certified product data for shipping, billing and final procurement.

Stainless Steel (SS) Coil: dimensions, density and unit-weight formula

Stainless Steel (SS) starts at 7900 kg/m³. Uses 304 as the generic stainless example; choose the actual grade rather than assuming all stainless has this density. Reference basis: 304 / EN 1.4301 representative.

The annular envelope represents the occupied winding space. A packing fraction describes the share occupied by metal rather than gaps. It is distinct from strip thickness; a strip-length calculation would instead use strip width, thickness and uncoiled length.

For stainless steel coil weight, keep a single physical piece definition: separate lengths, product counts and voids before multiplying. Convert dimensions consistently; millimetre volume scales by 10⁻⁹ to m³, while cubic inches use 0.0254³. Nominal designation and measured dimension are different inputs. Verify the drawing or product specification before interpreting a calculated total.

Check the numbers

Stainless Steel Coil Weight Calculator: calculated examples

These results are calculated from the dimensions or published-mass records stated in each row. They are not a complete inventory, certified tolerance table or structural design.

Worked example with stated inputs

Material density reference = Stainless Steel (SS); Shape = Coil; Dimension units = Millimetres (mm); Density (editable override) = 7900 kg/m³; Coil outside diameter = 1000 mm; Coil inside diameter = 508 mm; Coil axial width = 1000 mm; Metal packing fraction = 0.98 ratio; Quantity = 1 pieces; Optional unit price (0 = omit) = 0 ; Price basis = Price per kg; Cost currency label = USD.

OutputComputed result
Single-piece calculated mass4,511.38086 kg
Single-piece mass9,945.892299 lb
Quantity1 pieces
Total mass4,511.38086 kg
Total mass in pounds9,945.892299 lb
Net model metal volume0.571061 m³
Selected shapeCoil
Material referenceStainless Steel (SS)
Density entered7,900 kg/m³
Calculation basisGeometry × supplied density

Dimensioned weight examples in kg

ScenarioDimension set / calculation basisResult
500 mmCoil axial width2,255.69043 kg
750 mmCoil axial width3,383.535645 kg
1000 mmCoil axial width4,511.38086 kg
1500 mmCoil axial width6,767.07129 kg
2000 mmCoil axial width9,022.76172 kg
3000 mmCoil axial width13,534.142579 kg

Unchanged inputs use: Material density reference = Stainless Steel (SS); Shape = Coil; Dimension units = Millimetres (mm); Density (editable override) = 7900 kg/m³; Coil outside diameter = 1000 mm; Coil inside diameter = 508 mm; Coil axial width = 1000 mm; Metal packing fraction = 0.98 ratio; Quantity = 1 pieces; Optional unit price (0 = omit) = 0 ; Price basis = Price per kg; Cost currency label = USD. Results retain the model limitations described above.

Common questions

What density does this material weight calculator use?

Stainless Steel (SS) starts at 7900 kg/m³. Uses 304 as the generic stainless example; choose the actual grade rather than assuming all stainless has this density. Reference basis: 304 / EN 1.4301 representative.

What is the stainless steel coil weight calculation formula?

Vmetal = π(OD²−ID²) × coil width × packing fraction /4; mass = density × Vmetal. The initial density is 7900 kg/m³ for 304 / EN 1.4301 representative. The dimensioned examples on this page show the resulting piece mass; quantity and optional unit price are applied separately.

How do I calculate weight in kg and lbs?

The dimensional model gives metal volume in m³, multiplied by the entered kg/m³ density. One avoirdupois pound is exactly 0.45359237 kg. The result reports kg and lb; these are mass units, while force weight would require a gravitational acceleration.

Can I get weight per meter and per foot?

Uniform bars, pipes and section-area models report kg/m and lb/ft. One foot is exactly 0.3048 m. Area and nonuniform objects instead use their stated geometry; a sphere or coil does not have a meaningful generic straight-stock kg/m.

Does strip thickness appear in this coil formula?

Not in the annular-envelope method. Thickness and pitch affect packing and uncoiled length, which this tool does not infer.

Should I enter a steel core as metal?

No. This calculation excludes the inner bore and does not separately add core or packaging mass.

Can I export this calculation to Excel?

Calculate first, then choose Export CSV. The CSV contains the submitted model and inputs plus piece mass, total mass and applicable unit weights. Excel can open this text format; it is not a downloadable formula workbook or desktop application.

Does optional price include shipping or fabrication?

No. Enter a price per kg or per lb in the chosen currency label. The total is material mass times that unit price only, with no exchange-rate lookup, tax, minimum order, cutting loss or fabrication labor.

How should I read the calculated tables?

Each table states its geometry, material density and assumptions. Example dimensions are calculation scenarios unless explicitly identified as sourced nominal presets. They are not an inventory list or tolerance guarantee.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, certified tolerances or proprietary performance ratings.

  • OpenStax College Physics 2e, 11.2 Density: mass, volume and density relationshiphttps://openstax.org/books/college-physics-2e/pages/11-2-density
  • NIST SP 811, Appendix B.9: mass, length and derived-unit conversionshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors/nist-guide-si-appendix-b9
  • Euro Inox: Stainless Steel Tables of Technical Properties, 2007, physical properties pp. 16-17https://worldstainless.org/wp-content/uploads/2025/02/Tables_TechnicalProperties_EN.pdf