Metal Weight CalculatorMaterials, shapes & unit weights

Metal weight calculators / Stainless steel combinations

Metal by dimension. Mass by calculation.

Stainless Steel Disc Weight Calculator

Calculate stainless steel disc weight from actual dimensions, density and quantity. Read kg, lb and applicable unit weights, with an optional material-cost estimate.

Your material & dimensions

kg/m³
mm
mm
pieces

Preset densities are editable reference estimates. Dimensions use the selected mm/in unit. Published kg/m presets use their source mass directly; choose Custom dimensions to edit their geometry. Initial inputs are examples.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

V = π(OD²−ID²)t/4 − hole count × πdh²t/4; a disc uses ID=0 and no holes.

Calculate stainless steel disc weight from actual dimensions, density and quantity. Read kg, lb and applicable unit weights, with an optional material-cost estimate.

  1. Select a material reference, shape and a consistent dimension unit.
  2. Confirm metal density, actual dimensions and whether a nominal source preset applies.
  3. Submit the form, then interpret the result with the assumptions and limits below.

Flat blank only. Hole positions must not overlap each other or the bore/edge; a positive remaining volume does not prove a valid bolt layout. All dimensions are nominal or user supplied; use a scale or certified product data for shipping, billing and final procurement.

Stainless Steel (SS) Disc: dimensions, density and unit-weight formula

Stainless Steel (SS) starts at 7900 kg/m³. Uses 304 as the generic stainless example; choose the actual grade rather than assuming all stainless has this density. Reference basis: 304 / EN 1.4301 representative.

A ring or flat flange blank is an annular plate. Axial thickness differs from a pipe wall thickness. The optional flange holes remove ideal cylindrical volumes; this does not identify a pressure-class flange or include its hub and facing.

For stainless steel disc weight, keep a single physical piece definition: separate lengths, product counts and voids before multiplying. Convert dimensions consistently; millimetre volume scales by 10⁻⁹ to m³, while cubic inches use 0.0254³. Nominal designation and measured dimension are different inputs. Verify the drawing or product specification before interpreting a calculated total.

Check the numbers

Stainless Steel Disc Weight Calculator: calculated examples

These results are calculated from the dimensions or published-mass records stated in each row. They are not a complete inventory, certified tolerance table or structural design.

Worked example with stated inputs

Material density reference = Stainless Steel (SS); Shape = Disc; Dimension units = Millimetres (mm); Density (editable override) = 7900 kg/m³; Outside diameter = 200 mm; Axial thickness = 10 mm; Quantity = 1 pieces; Optional unit price (0 = omit) = 0 ; Price basis = Price per kg; Cost currency label = USD.

OutputComputed result
Single-piece calculated mass2.481858 kg
Single-piece mass5.471561 lb
Quantity1 pieces
Total mass2.481858 kg
Total mass in pounds5.471561 lb
Net model metal volume0.000314 m³
Selected shapeDisc
Material referenceStainless Steel (SS)
Density entered7,900 kg/m³
Calculation basisGeometry × supplied density

Dimensioned weight examples in kg

ScenarioDimension set / calculation basisResult
5 mmAxial thickness1.240929 kg
7.5 mmAxial thickness1.861394 kg
10 mmAxial thickness2.481858 kg
15 mmAxial thickness3.722787 kg
20 mmAxial thickness4.963716 kg
30 mmAxial thickness7.445575 kg

Unchanged inputs use: Material density reference = Stainless Steel (SS); Shape = Disc; Dimension units = Millimetres (mm); Density (editable override) = 7900 kg/m³; Outside diameter = 200 mm; Axial thickness = 10 mm; Quantity = 1 pieces; Optional unit price (0 = omit) = 0 ; Price basis = Price per kg; Cost currency label = USD. Results retain the model limitations described above.

Common questions

What density does this material weight calculator use?

Stainless Steel (SS) starts at 7900 kg/m³. Uses 304 as the generic stainless example; choose the actual grade rather than assuming all stainless has this density. Reference basis: 304 / EN 1.4301 representative.

What is the stainless steel disc weight calculation formula?

V = π(OD²−ID²)t/4 − hole count × πdh²t/4; a disc uses ID=0 and no holes. The initial density is 7900 kg/m³ for 304 / EN 1.4301 representative. The dimensioned examples on this page show the resulting piece mass; quantity and optional unit price are applied separately.

How do I calculate weight in kg and lbs?

The dimensional model gives metal volume in m³, multiplied by the entered kg/m³ density. One avoirdupois pound is exactly 0.45359237 kg. The result reports kg and lb; these are mass units, while force weight would require a gravitational acceleration.

Can I get weight per meter and per foot?

Uniform bars, pipes and section-area models report kg/m and lb/ft. One foot is exactly 0.3048 m. Area and nonuniform objects instead use their stated geometry; a sphere or coil does not have a meaningful generic straight-stock kg/m.

Does this calculate an ASME pressure-class flange?

No. A finished flange can have a hub, neck, raised face and recesses. Use a detailed drawing or supplier mass for the finished part.

Can this include drilled holes?

The flange blank mode subtracts the supplied through-hole count and diameter. It does not validate bolt-circle spacing or edge distances.

Can I export this calculation to Excel?

Calculate first, then choose Export CSV. The CSV contains the submitted model and inputs plus piece mass, total mass and applicable unit weights. Excel can open this text format; it is not a downloadable formula workbook or desktop application.

Does optional price include shipping or fabrication?

No. Enter a price per kg or per lb in the chosen currency label. The total is material mass times that unit price only, with no exchange-rate lookup, tax, minimum order, cutting loss or fabrication labor.

How should I read the calculated tables?

Each table states its geometry, material density and assumptions. Example dimensions are calculation scenarios unless explicitly identified as sourced nominal presets. They are not an inventory list or tolerance guarantee.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, certified tolerances or proprietary performance ratings.

  • OpenStax College Physics 2e, 11.2 Density: mass, volume and density relationshiphttps://openstax.org/books/college-physics-2e/pages/11-2-density
  • NIST SP 811, Appendix B.9: mass, length and derived-unit conversionshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors/nist-guide-si-appendix-b9
  • Euro Inox: Stainless Steel Tables of Technical Properties, 2007, physical properties pp. 16-17https://worldstainless.org/wp-content/uploads/2025/02/Tables_TechnicalProperties_EN.pdf