Metal weight calculators / Stainless steel combinations
Metal by dimension. Mass by calculation.
Stainless Steel Pipe Weight Calculator
Calculate stainless steel pipe weight from actual dimensions, density and quantity. Read kg, lb and applicable unit weights, with an optional material-cost estimate.
Your material & dimensions
Your result
Ready to calculateEnter your values and press Calculate. The result will open on the calculation page.
Published references · Clear assumptions · No sign-up
The method
Formula and calculation steps
ID = OD − 2t; A = π(OD² − ID²)/4; mass = density × A × length.
Calculate stainless steel pipe weight from actual dimensions, density and quantity. Read kg, lb and applicable unit weights, with an optional material-cost estimate.
- Select a material reference, shape and a consistent dimension unit.
- Confirm metal density, actual dimensions and whether a nominal source preset applies.
- Submit the form, then interpret the result with the assumptions and limits below.
Straight hollow circular section, positive bore required. No fittings, seam allowance, lining, thread loss or coating unless separately stated. All dimensions are nominal or user supplied; use a scale or certified product data for shipping, billing and final procurement.
Stainless Steel (SS) Pipe: dimensions, density and unit-weight formula
Stainless Steel (SS) starts at 7900 kg/m³. Uses 304 as the generic stainless example; choose the actual grade rather than assuming all stainless has this density. Reference basis: 304 / EN 1.4301 representative.
Use actual outside diameter and wall thickness. Nominal pipe size is a designation, not a measured outside diameter. Pipe schedules, tube gauge systems and delivered tolerances must be resolved before using dimensional arithmetic.
For stainless steel pipe weight, keep a single physical piece definition: separate lengths, product counts and voids before multiplying. Convert dimensions consistently; millimetre volume scales by 10⁻⁹ to m³, while cubic inches use 0.0254³. Nominal designation and measured dimension are different inputs. Verify the drawing or product specification before interpreting a calculated total.
Continue with: SS 202 Sheet Weight Calculator · SS 304 Angle Weight Calculator · SS 304 Channel Weight Calculator · SS 304 Checker Plate Weight Calculator
Check the numbers
Stainless Steel Pipe Weight Calculator: calculated examples
These results are calculated from the dimensions or published-mass records stated in each row. They are not a complete inventory, certified tolerance table or structural design.
Worked example with stated inputs
Material density reference = Stainless Steel (SS); Shape = Pipe; Dimension units = Millimetres (mm); Density (editable override) = 7900 kg/m³; Dimension / published-mass preset = Custom dimensions; Outside / solid diameter = 21.336 mm; Wall thickness = 2.1082 mm; Piece / sidewall length = 1000 mm; Quantity = 1 pieces; Optional unit price (0 = omit) = 0 ; Price basis = Price per kg; Cost currency label = USD.
| Output | Computed result |
|---|---|
| Single-piece calculated mass | 1.006047 kg |
| Single-piece mass | 2.217954 lb |
| Quantity | 1 pieces |
| Total mass | 1.006047 kg |
| Total mass in pounds | 2.217954 lb |
| Linear mass | 1.006047 kg/m |
| Linear mass in imperial units | 0.676033 lb/ft |
| Net model metal volume | 0.000127 m³ |
| Selected shape | Pipe |
| Material reference | Stainless Steel (SS) |
| Density entered | 7,900 kg/m³ |
| Calculation basis | Geometry × supplied density |
Dimensioned weight examples in kg
| Scenario | Dimension set / calculation basis | Result |
|---|---|---|
| NPS 1/2 Sch 10S | diameter 21.336 mm, thickness 2.1082 mm | 1.006047 kg |
| NPS 1/2 Sch 40S | diameter 21.336 mm, thickness 2.7686 mm | 1.275817 kg |
| NPS 3/4 Sch 10S | diameter 26.67 mm, thickness 2.1082 mm | 1.285136 kg |
| NPS 3/4 Sch 40S | diameter 26.67 mm, thickness 2.8702 mm | 1.695362 kg |
| NPS 1 Sch 10S | diameter 33.401 mm, thickness 2.7686 mm | 2.104836 kg |
| NPS 1 Sch 40S | diameter 33.401 mm, thickness 3.3782 mm | 2.517176 kg |
| NPS 2 Sch 10S | diameter 60.325 mm, thickness 2.7686 mm | 3.954857 kg |
| NPS 2 Sch 40S | diameter 60.325 mm, thickness 3.9116 mm | 5.476633 kg |
Unchanged inputs use: Material density reference = Stainless Steel (SS); Shape = Pipe; Dimension units = Millimetres (mm); Density (editable override) = 7900 kg/m³; Dimension / published-mass preset = Custom dimensions; Outside / solid diameter = 21.336 mm; Wall thickness = 2.1082 mm; Piece / sidewall length = 1000 mm; Quantity = 1 pieces; Optional unit price (0 = omit) = 0 ; Price basis = Price per kg; Cost currency label = USD. Results retain the model limitations described above.
Common questions
What density does this material weight calculator use?
Stainless Steel (SS) starts at 7900 kg/m³. Uses 304 as the generic stainless example; choose the actual grade rather than assuming all stainless has this density. Reference basis: 304 / EN 1.4301 representative.
What is the stainless steel pipe weight calculation formula?
ID = OD − 2t; A = π(OD² − ID²)/4; mass = density × A × length. The initial density is 7900 kg/m³ for 304 / EN 1.4301 representative. The dimensioned examples on this page show the resulting piece mass; quantity and optional unit price are applied separately.
How do I calculate weight in kg and lbs?
The dimensional model gives metal volume in m³, multiplied by the entered kg/m³ density. One avoirdupois pound is exactly 0.45359237 kg. The result reports kg and lb; these are mass units, while force weight would require a gravitational acceleration.
Can I get weight per meter and per foot?
Uniform bars, pipes and section-area models report kg/m and lb/ft. One foot is exactly 0.3048 m. Area and nonuniform objects instead use their stated geometry; a sphere or coil does not have a meaningful generic straight-stock kg/m.
Can I enter NPS or DN as outside diameter?
No. Use the dimensional standard or supplier drawing to find actual OD. The schedule table tool supplies a few explicitly sourced pipe examples.
How are the sourced size presets different from custom geometry?
A dimensional preset supplies published nominal OD and wall. A published-mass preset uses its source kg/m directly and ignores density for that mass. Select Custom dimensions for the simple geometric estimate. These two bases can differ because of fillets, manufacturing conventions and catalogue rounding.
Is wall thickness equal to a schedule number?
No. Schedule 10S or 40S is a series whose wall depends on nominal size. Enter the actual decimal thickness, or use a sourced preset.
Can I export this calculation to Excel?
Calculate first, then choose Export CSV. The CSV contains the submitted model and inputs plus piece mass, total mass and applicable unit weights. Excel can open this text format; it is not a downloadable formula workbook or desktop application.
Does optional price include shipping or fabrication?
No. Enter a price per kg or per lb in the chosen currency label. The total is material mass times that unit price only, with no exchange-rate lookup, tax, minimum order, cutting loss or fabrication labor.
How should I read the calculated tables?
Each table states its geometry, material density and assumptions. Example dimensions are calculation scenarios unless explicitly identified as sourced nominal presets. They are not an inventory list or tolerance guarantee.
Related calculators
Formula sources and references
References support the underlying methods and units. Chosen example inputs are not universal recommendations, certified tolerances or proprietary performance ratings.
- OpenStax College Physics 2e, 11.2 Density: mass, volume and density relationshiphttps://openstax.org/books/college-physics-2e/pages/11-2-density
- NIST SP 811, Appendix B.9: mass, length and derived-unit conversionshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors/nist-guide-si-appendix-b9
- Euro Inox: Stainless Steel Tables of Technical Properties, 2007, physical properties pp. 16-17https://worldstainless.org/wp-content/uploads/2025/02/Tables_TechnicalProperties_EN.pdf
- Penn Stainless Products: Pipe Dimensions, nominal OD and wall in inches; NPS 1/2, 3/4, 1 and 2, Schedule 10S and 40S rowshttps://www.pennstainless.com/resources/product-resources/pipe-dimensions/
- ASME B36.19-2022: Welded and Seamless Wrought Stainless Steel Pipe; Publisher cover and table of contentshttps://www.asme.org/getmedia/a9eaf44a-2fd2-4063-a6e5-c648750bf781/table-of-contents_b36-19-2022.pdf