Metal weight calculators / Stainless steel combinations
Metal by dimension. Mass by calculation.
Stainless Steel Square Tube Weight Calculator
Calculate stainless steel square tube weight from actual dimensions, density and quantity. Read kg, lb and applicable unit weights, with an optional material-cost estimate.
Your material & dimensions
Your result
Ready to calculateEnter your values and press Calculate. The result will open on the calculation page.
Published references · Clear assumptions · No sign-up
The method
Formula and calculation steps
A = B×H − (B−2t)(H−2t); for SHS set H=B; mass = density × A × length.
Calculate stainless steel square tube weight from actual dimensions, density and quantity. Read kg, lb and applicable unit weights, with an optional material-cost estimate.
- Select a material reference, shape and a consistent dimension unit.
- Confirm metal density, actual dimensions and whether a nominal source preset applies.
- Submit the form, then interpret the result with the assumptions and limits below.
Sharp-corner approximation, not an EN/ASTM hollow-section certified mass. All dimensions are nominal or user supplied; use a scale or certified product data for shipping, billing and final procurement.
Stainless Steel (SS) Square Hollow Section (SHS): dimensions, density and unit-weight formula
Stainless Steel (SS) starts at 7900 kg/m³. Uses 304 as the generic stainless example; choose the actual grade rather than assuming all stainless has this density. Reference basis: 304 / EN 1.4301 representative.
Subtract the inner rectangular opening from the outer rectangle. This transparent estimate uses sharp corners and uniform thickness. Real cold-formed hollow sections have rounded corners, so a supplier certified section area is preferable for an exact catalogue estimate.
For stainless steel square tube weight, keep a single physical piece definition: separate lengths, product counts and voids before multiplying. Convert dimensions consistently; millimetre volume scales by 10⁻⁹ to m³, while cubic inches use 0.0254³. Nominal designation and measured dimension are different inputs. Verify the drawing or product specification before interpreting a calculated total.
Continue with: SS 202 Sheet Weight Calculator · SS 304 Angle Weight Calculator · SS 304 Channel Weight Calculator · SS 304 Checker Plate Weight Calculator
Check the numbers
Stainless Steel Square Tube Weight Calculator: calculated examples
These results are calculated from the dimensions or published-mass records stated in each row. They are not a complete inventory, certified tolerance table or structural design.
Worked example with stated inputs
Material density reference = Stainless Steel (SS); Shape = Square Hollow Section (SHS); Dimension units = Millimetres (mm); Density (editable override) = 7900 kg/m³; Outside square side = 50 mm; Wall thickness = 3 mm; Piece / sidewall length = 1000 mm; Quantity = 1 pieces; Optional unit price (0 = omit) = 0 ; Price basis = Price per kg; Cost currency label = USD.
| Output | Computed result |
|---|---|
| Single-piece calculated mass | 4.4556 kg |
| Single-piece mass | 9.822917 lb |
| Quantity | 1 pieces |
| Total mass | 4.4556 kg |
| Total mass in pounds | 9.822917 lb |
| Linear mass | 4.4556 kg/m |
| Linear mass in imperial units | 2.994025 lb/ft |
| Net model metal volume | 0.000564 m³ |
| Selected shape | Square Hollow Section (SHS) |
| Material reference | Stainless Steel (SS) |
| Density entered | 7,900 kg/m³ |
| Calculation basis | Geometry × supplied density |
Dimensioned weight examples in kg
| Scenario | Dimension set / calculation basis | Result |
|---|---|---|
| 500 mm | Piece / sidewall length | 2.2278 kg |
| 750 mm | Piece / sidewall length | 3.3417 kg |
| 1000 mm | Piece / sidewall length | 4.4556 kg |
| 1500 mm | Piece / sidewall length | 6.6834 kg |
| 2000 mm | Piece / sidewall length | 8.9112 kg |
| 3000 mm | Piece / sidewall length | 13.3668 kg |
Unchanged inputs use: Material density reference = Stainless Steel (SS); Shape = Square Hollow Section (SHS); Dimension units = Millimetres (mm); Density (editable override) = 7900 kg/m³; Outside square side = 50 mm; Wall thickness = 3 mm; Piece / sidewall length = 1000 mm; Quantity = 1 pieces; Optional unit price (0 = omit) = 0 ; Price basis = Price per kg; Cost currency label = USD. Results retain the model limitations described above.
Common questions
What density does this material weight calculator use?
Stainless Steel (SS) starts at 7900 kg/m³. Uses 304 as the generic stainless example; choose the actual grade rather than assuming all stainless has this density. Reference basis: 304 / EN 1.4301 representative.
What is the stainless steel square tube weight calculation formula?
A = B×H − (B−2t)(H−2t); for SHS set H=B; mass = density × A × length. The initial density is 7900 kg/m³ for 304 / EN 1.4301 representative. The dimensioned examples on this page show the resulting piece mass; quantity and optional unit price are applied separately.
How do I calculate weight in kg and lbs?
The dimensional model gives metal volume in m³, multiplied by the entered kg/m³ density. One avoirdupois pound is exactly 0.45359237 kg. The result reports kg and lb; these are mass units, while force weight would require a gravitational acceleration.
Can I get weight per meter and per foot?
Uniform bars, pipes and section-area models report kg/m and lb/ft. One foot is exactly 0.3048 m. Area and nonuniform objects instead use their stated geometry; a sphere or coil does not have a meaningful generic straight-stock kg/m.
Does this account for rounded hollow-section corners?
No. Enter the published area in the section-area calculator when corner radii and production details matter.
Can the wall equal half the smaller outside side?
No. That would remove the bore and is rejected. Use a solid bar calculator for a solid section.
Can I export this calculation to Excel?
Calculate first, then choose Export CSV. The CSV contains the submitted model and inputs plus piece mass, total mass and applicable unit weights. Excel can open this text format; it is not a downloadable formula workbook or desktop application.
Does optional price include shipping or fabrication?
No. Enter a price per kg or per lb in the chosen currency label. The total is material mass times that unit price only, with no exchange-rate lookup, tax, minimum order, cutting loss or fabrication labor.
How should I read the calculated tables?
Each table states its geometry, material density and assumptions. Example dimensions are calculation scenarios unless explicitly identified as sourced nominal presets. They are not an inventory list or tolerance guarantee.
Related calculators
Formula sources and references
References support the underlying methods and units. Chosen example inputs are not universal recommendations, certified tolerances or proprietary performance ratings.
- OpenStax College Physics 2e, 11.2 Density: mass, volume and density relationshiphttps://openstax.org/books/college-physics-2e/pages/11-2-density
- NIST SP 811, Appendix B.9: mass, length and derived-unit conversionshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors/nist-guide-si-appendix-b9
- Euro Inox: Stainless Steel Tables of Technical Properties, 2007, physical properties pp. 16-17https://worldstainless.org/wp-content/uploads/2025/02/Tables_TechnicalProperties_EN.pdf