Metal weight calculators / Published size samples
Metal by dimension. Mass by calculation.
W Shape Beam Weight Calculator
Choose a representative published size, enter cut length and quantity, and calculate mass in kg and lb. These are sourced examples rather than a complete standard database.
Your material & dimensions
Your result
Ready to calculateEnter your values and press Calculate. The result will open on the calculation page.
Published references · Clear assumptions · No sign-up
The method
Formula and calculation steps
Mass = published linear mass × cut length; total = piece mass × quantity.
Choose a representative published size, enter cut length and quantity, and calculate mass in kg and lb. These are sourced examples rather than a complete standard database.
- Select a material reference, shape and a consistent dimension unit.
- Confirm metal density, actual dimensions and whether a nominal source preset applies.
- Submit the form, then interpret the result with the assumptions and limits below.
Only the listed representative source records are built in, not the full standard. Published linear mass is multiplied by cut length; density does not rescale a published kg/m value. No structural load or pressure certification.
Steel Section Area: dimensions, density and unit-weight formula
Steel starts at 7850 kg/m³. A conventional structural-steel estimate. Select the actual alloy or enter certified density when known. Reference basis: Representative structural steel.
Use the actual metal cross-section area from a supplier or a validated drawing. It includes fillets, hollows and extrusion details when those are already included in the area. A bounding rectangle or outer silhouette is not necessarily the metal area.
For w shape beam weight, keep a single physical piece definition: separate lengths, product counts and voids before multiplying. Convert dimensions consistently; millimetre volume scales by 10⁻⁹ to m³, while cubic inches use 0.0254³. Nominal designation and measured dimension are different inputs. Verify the drawing or product specification before interpreting a calculated total.
Continue with: Stainless Pipe Schedule Weight Calculator · Copper Tube K L M Weight Calculator · ISMB Beam Weight Calculator · ISMC Channel Weight Calculator
Check the numbers
W Shape Beam Weight Calculator: calculated examples
These results are calculated from the dimensions or published-mass records stated in each row. They are not a complete inventory, certified tolerance table or structural design.
Worked example with stated inputs
Material density reference = Steel; Shape = Section Area; Dimension units = Millimetres (mm); Density (editable override) = 7850 kg/m³; Dimension / published-mass preset = W6x8.5; Cut length = 1000 mm; Quantity = 1 pieces; Optional unit price (0 = omit) = 0 ; Price basis = Price per kg; Cost currency label = USD.
| Output | Computed result |
|---|---|
| Single-piece calculated mass | 12.649394 kg |
| Single-piece mass | 27.887139 lb |
| Quantity | 1 pieces |
| Total mass | 12.649394 kg |
| Total mass in pounds | 27.887139 lb |
| Linear mass | 12.649394 kg/m |
| Linear mass in imperial units | 8.5 lb/ft |
| Selected shape | Section Area |
| Material reference | Steel |
| Density input (unused for this mass basis) | 7,850 kg/m³ |
| Calculation basis | W6x8.5 |
Dimensioned weight examples in kg
| Scenario | Dimension set / calculation basis | Result |
|---|---|---|
| W6x8.5 | Published nominal kg/m × 1 m | 12.649394 kg |
| W6x12 | Published nominal kg/m × 1 m | 17.857967 kg |
| W8x10 | Published nominal kg/m × 1 m | 14.881639 kg |
| W8x13 | Published nominal kg/m × 1 m | 19.346131 kg |
Unchanged inputs use: Material density reference = Steel; Shape = Section Area; Dimension units = Millimetres (mm); Density (editable override) = 7850 kg/m³; Dimension / published-mass preset = W6x8.5; Cut length = 1000 mm; Quantity = 1 pieces; Optional unit price (0 = omit) = 0 ; Price basis = Price per kg; Cost currency label = USD. Results retain the model limitations described above.
Common questions
Is this a complete standard weight chart?
No. It provides a small set of attributed published records and computes new cut-length and quantity totals from them. Use the current applicable standard and supplier for the full range, dimensional tolerances and certification.
What is the w shape beam weight calculation formula?
Mass = published linear mass × cut length; total = piece mass × quantity. The initial density is 7850 kg/m³ for Representative structural steel. The dimensioned examples on this page show the resulting piece mass; quantity and optional unit price are applied separately.
What density does this material weight calculator use?
Steel starts at 7850 kg/m³. A conventional structural-steel estimate. Select the actual alloy or enter certified density when known. Reference basis: Representative structural steel.
How do I calculate weight in kg and lbs?
The dimensional model gives metal volume in m³, multiplied by the entered kg/m³ density. One avoirdupois pound is exactly 0.45359237 kg. The result reports kg and lb; these are mass units, while force weight would require a gravitational acceleration.
Can I get weight per meter and per foot?
Uniform bars, pipes and section-area models report kg/m and lb/ft. One foot is exactly 0.3048 m. Area and nonuniform objects instead use their stated geometry; a sphere or coil does not have a meaningful generic straight-stock kg/m.
Can I use a standard section area from a catalogue?
Yes, provided its units, metal grade and definition are correct. Published nominal kg/m can differ slightly because area and mass may be independently rounded.
How are the sourced size presets different from custom geometry?
A dimensional preset supplies published nominal OD and wall. A published-mass preset uses its source kg/m directly and ignores density for that mass. Select Custom dimensions for the simple geometric estimate. These two bases can differ because of fillets, manufacturing conventions and catalogue rounding.
What about an aluminum extrusion or conductor cable?
Enter the sum of its true metal areas. Separate different materials, voids and insulation, and account for nonstraight lay paths when applicable.
Can I export this calculation to Excel?
Calculate first, then choose Export CSV. The CSV contains the submitted model and inputs plus piece mass, total mass and applicable unit weights. Excel can open this text format; it is not a downloadable formula workbook or desktop application.
Does optional price include shipping or fabrication?
No. Enter a price per kg or per lb in the chosen currency label. The total is material mass times that unit price only, with no exchange-rate lookup, tax, minimum order, cutting loss or fabrication labor.
How should I read the calculated tables?
Each table states its geometry, material density and assumptions. Example dimensions are calculation scenarios unless explicitly identified as sourced nominal presets. They are not an inventory list or tolerance guarantee.
Related calculators
Formula sources and references
References support the underlying methods and units. Chosen example inputs are not universal recommendations, certified tolerances or proprietary performance ratings.
- OpenStax College Physics 2e, 11.2 Density: mass, volume and density relationshiphttps://openstax.org/books/college-physics-2e/pages/11-2-density
- NIST SP 811, Appendix B.9: mass, length and derived-unit conversionshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors/nist-guide-si-appendix-b9
- SSAB structural hollow sections EPD: steel densityhttps://websitecdn.ssab.com/-/media/Files/EN/Support/Certificates/Hollow-Sections/Environmental-product-declaration---EN-EPD-SSAB-tubes-sections-piles.pdf
- Gerdau: Wide Flange Beams for Solar Posts; PDF page 1 of 1, Dimensions and Properties tablehttps://www2.gerdau.com/sites/gln_gerdau/files/downloadable_files/Gerdau-Solar-Posts-Data-Sheet_1_0.pdf