Metal Weight CalculatorMaterials, shapes & unit weights

Metal weight calculators / Aluminium combinations

Metal by dimension. Mass by calculation.

Aluminum Rectangular Tube Weight Calculator

Calculate aluminum rectangular tube weight from actual dimensions, density and quantity. Read kg, lb and applicable unit weights, with an optional material-cost estimate.

Your material & dimensions

kg/m³
mm
mm
mm
mm
pieces

Preset densities are editable reference estimates. Dimensions use the selected mm/in unit. Published kg/m presets use their source mass directly; choose Custom dimensions to edit their geometry. Initial inputs are examples.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

A = B×H − (B−2t)(H−2t); for SHS set H=B; mass = density × A × length.

Calculate aluminum rectangular tube weight from actual dimensions, density and quantity. Read kg, lb and applicable unit weights, with an optional material-cost estimate.

  1. Select a material reference, shape and a consistent dimension unit.
  2. Confirm metal density, actual dimensions and whether a nominal source preset applies.
  3. Submit the form, then interpret the result with the assumptions and limits below.

Sharp-corner approximation, not an EN/ASTM hollow-section certified mass. All dimensions are nominal or user supplied; use a scale or certified product data for shipping, billing and final procurement.

Aluminium / Aluminum Rectangular Hollow Section (RHS): dimensions, density and unit-weight formula

Aluminium / Aluminum starts at 2700 kg/m³. Elemental aluminium reference. Alloy, temper, product tolerances and surface layers can change the actual mass. Reference basis: Elemental aluminium at/near room temperature.

Subtract the inner rectangular opening from the outer rectangle. This transparent estimate uses sharp corners and uniform thickness. Real cold-formed hollow sections have rounded corners, so a supplier certified section area is preferable for an exact catalogue estimate.

For aluminum rectangular tube weight, keep a single physical piece definition: separate lengths, product counts and voids before multiplying. Convert dimensions consistently; millimetre volume scales by 10⁻⁹ to m³, while cubic inches use 0.0254³. Nominal designation and measured dimension are different inputs. Verify the drawing or product specification before interpreting a calculated total.

Check the numbers

Aluminum Rectangular Tube Weight Calculator: calculated examples

These results are calculated from the dimensions or published-mass records stated in each row. They are not a complete inventory, certified tolerance table or structural design.

Worked example with stated inputs

Material density reference = Aluminium / Aluminum; Shape = Rectangular Hollow Section (RHS); Dimension units = Millimetres (mm); Density (editable override) = 2700 kg/m³; Overall width / first side = 50 mm; Overall height / second side = 100 mm; Wall thickness = 3 mm; Piece / sidewall length = 1000 mm; Quantity = 1 pieces; Optional unit price (0 = omit) = 0 ; Price basis = Price per kg; Cost currency label = USD.

OutputComputed result
Single-piece calculated mass2.3328 kg
Single-piece mass5.142944 lb
Quantity1 pieces
Total mass2.3328 kg
Total mass in pounds5.142944 lb
Linear mass2.3328 kg/m
Linear mass in imperial units1.567569 lb/ft
Net model metal volume0.000864 m³
Selected shapeRectangular Hollow Section (RHS)
Material referenceAluminium / Aluminum
Density entered2,700 kg/m³
Calculation basisGeometry × supplied density

Dimensioned weight examples in kg

ScenarioDimension set / calculation basisResult
500 mmPiece / sidewall length1.1664 kg
750 mmPiece / sidewall length1.7496 kg
1000 mmPiece / sidewall length2.3328 kg
1500 mmPiece / sidewall length3.4992 kg
2000 mmPiece / sidewall length4.6656 kg
3000 mmPiece / sidewall length6.9984 kg

Unchanged inputs use: Material density reference = Aluminium / Aluminum; Shape = Rectangular Hollow Section (RHS); Dimension units = Millimetres (mm); Density (editable override) = 2700 kg/m³; Overall width / first side = 50 mm; Overall height / second side = 100 mm; Wall thickness = 3 mm; Piece / sidewall length = 1000 mm; Quantity = 1 pieces; Optional unit price (0 = omit) = 0 ; Price basis = Price per kg; Cost currency label = USD. Results retain the model limitations described above.

Common questions

What density does this material weight calculator use?

Aluminium / Aluminum starts at 2700 kg/m³. Elemental aluminium reference. Alloy, temper, product tolerances and surface layers can change the actual mass. Reference basis: Elemental aluminium at/near room temperature.

What is the aluminum rectangular tube weight calculation formula?

A = B×H − (B−2t)(H−2t); for SHS set H=B; mass = density × A × length. The initial density is 2700 kg/m³ for Elemental aluminium at/near room temperature. The dimensioned examples on this page show the resulting piece mass; quantity and optional unit price are applied separately.

Are aluminum and aluminium different materials?

They are US and international spellings of the same element. Alloy and temper designations still matter: a generic aluminum preset is not a density certificate for every casting or wrought alloy.

How do I calculate weight in kg and lbs?

The dimensional model gives metal volume in m³, multiplied by the entered kg/m³ density. One avoirdupois pound is exactly 0.45359237 kg. The result reports kg and lb; these are mass units, while force weight would require a gravitational acceleration.

Can I get weight per meter and per foot?

Uniform bars, pipes and section-area models report kg/m and lb/ft. One foot is exactly 0.3048 m. Area and nonuniform objects instead use their stated geometry; a sphere or coil does not have a meaningful generic straight-stock kg/m.

Does this account for rounded hollow-section corners?

No. Enter the published area in the section-area calculator when corner radii and production details matter.

Can the wall equal half the smaller outside side?

No. That would remove the bore and is rejected. Use a solid bar calculator for a solid section.

Can I export this calculation to Excel?

Calculate first, then choose Export CSV. The CSV contains the submitted model and inputs plus piece mass, total mass and applicable unit weights. Excel can open this text format; it is not a downloadable formula workbook or desktop application.

Does optional price include shipping or fabrication?

No. Enter a price per kg or per lb in the chosen currency label. The total is material mass times that unit price only, with no exchange-rate lookup, tax, minimum order, cutting loss or fabrication labor.

How should I read the calculated tables?

Each table states its geometry, material density and assumptions. Example dimensions are calculation scenarios unless explicitly identified as sourced nominal presets. They are not an inventory list or tolerance guarantee.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, certified tolerances or proprietary performance ratings.

  • OpenStax College Physics 2e, 11.2 Density: mass, volume and density relationshiphttps://openstax.org/books/college-physics-2e/pages/11-2-density
  • NIST SP 811, Appendix B.9: mass, length and derived-unit conversionshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors/nist-guide-si-appendix-b9
  • NIST SRD 71 Users Guide, Table A.3: elemental solids at/near room temperaturehttps://www.nist.gov/system/files/documents/srd/SRD71UsersGuideV1-2.pdf