Metal Weight CalculatorMaterials, shapes & unit weights

Metal weight calculators / Aluminium combinations

Metal by dimension. Mass by calculation.

Aluminum Tube Weight Calculator

Calculate aluminum tube weight from actual dimensions, density and quantity. Read kg, lb and applicable unit weights, with an optional material-cost estimate.

Your material & dimensions

kg/m³
mm
mm
mm
pieces

Preset densities are editable reference estimates. Dimensions use the selected mm/in unit. Published kg/m presets use their source mass directly; choose Custom dimensions to edit their geometry. Initial inputs are examples.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

ID = OD − 2t; A = π(OD² − ID²)/4; mass = density × A × length.

Calculate aluminum tube weight from actual dimensions, density and quantity. Read kg, lb and applicable unit weights, with an optional material-cost estimate.

  1. Select a material reference, shape and a consistent dimension unit.
  2. Confirm metal density, actual dimensions and whether a nominal source preset applies.
  3. Submit the form, then interpret the result with the assumptions and limits below.

Straight hollow circular section, positive bore required. No fittings, seam allowance, lining, thread loss or coating unless separately stated. All dimensions are nominal or user supplied; use a scale or certified product data for shipping, billing and final procurement.

Aluminium / Aluminum Round Tube: dimensions, density and unit-weight formula

Aluminium / Aluminum starts at 2700 kg/m³. Elemental aluminium reference. Alloy, temper, product tolerances and surface layers can change the actual mass. Reference basis: Elemental aluminium at/near room temperature.

Use actual outside diameter and wall thickness. Nominal pipe size is a designation, not a measured outside diameter. Pipe schedules, tube gauge systems and delivered tolerances must be resolved before using dimensional arithmetic.

For aluminum tube weight, keep a single physical piece definition: separate lengths, product counts and voids before multiplying. Convert dimensions consistently; millimetre volume scales by 10⁻⁹ to m³, while cubic inches use 0.0254³. Nominal designation and measured dimension are different inputs. Verify the drawing or product specification before interpreting a calculated total.

Check the numbers

Aluminum Tube Weight Calculator: calculated examples

These results are calculated from the dimensions or published-mass records stated in each row. They are not a complete inventory, certified tolerance table or structural design.

Worked example with stated inputs

Material density reference = Aluminium / Aluminum; Shape = Round Tube; Dimension units = Millimetres (mm); Density (editable override) = 2700 kg/m³; Outside / solid diameter = 50 mm; Wall thickness = 3 mm; Piece / sidewall length = 1000 mm; Quantity = 1 pieces; Optional unit price (0 = omit) = 0 ; Price basis = Price per kg; Cost currency label = USD.

OutputComputed result
Single-piece calculated mass1.196004 kg
Single-piece mass2.636738 lb
Quantity1 pieces
Total mass1.196004 kg
Total mass in pounds2.636738 lb
Linear mass1.196004 kg/m
Linear mass in imperial units0.803678 lb/ft
Net model metal volume0.000443 m³
Selected shapeRound Tube
Material referenceAluminium / Aluminum
Density entered2,700 kg/m³
Calculation basisGeometry × supplied density

Dimensioned weight examples in kg

ScenarioDimension set / calculation basisResult
500 mmPiece / sidewall length0.598002 kg
750 mmPiece / sidewall length0.897003 kg
1000 mmPiece / sidewall length1.196004 kg
1500 mmPiece / sidewall length1.794006 kg
2000 mmPiece / sidewall length2.392009 kg
3000 mmPiece / sidewall length3.588013 kg

Unchanged inputs use: Material density reference = Aluminium / Aluminum; Shape = Round Tube; Dimension units = Millimetres (mm); Density (editable override) = 2700 kg/m³; Outside / solid diameter = 50 mm; Wall thickness = 3 mm; Piece / sidewall length = 1000 mm; Quantity = 1 pieces; Optional unit price (0 = omit) = 0 ; Price basis = Price per kg; Cost currency label = USD. Results retain the model limitations described above.

Common questions

What density does this material weight calculator use?

Aluminium / Aluminum starts at 2700 kg/m³. Elemental aluminium reference. Alloy, temper, product tolerances and surface layers can change the actual mass. Reference basis: Elemental aluminium at/near room temperature.

What is the aluminum tube weight calculation formula?

ID = OD − 2t; A = π(OD² − ID²)/4; mass = density × A × length. The initial density is 2700 kg/m³ for Elemental aluminium at/near room temperature. The dimensioned examples on this page show the resulting piece mass; quantity and optional unit price are applied separately.

Are aluminum and aluminium different materials?

They are US and international spellings of the same element. Alloy and temper designations still matter: a generic aluminum preset is not a density certificate for every casting or wrought alloy.

How do I calculate weight in kg and lbs?

The dimensional model gives metal volume in m³, multiplied by the entered kg/m³ density. One avoirdupois pound is exactly 0.45359237 kg. The result reports kg and lb; these are mass units, while force weight would require a gravitational acceleration.

Can I get weight per meter and per foot?

Uniform bars, pipes and section-area models report kg/m and lb/ft. One foot is exactly 0.3048 m. Area and nonuniform objects instead use their stated geometry; a sphere or coil does not have a meaningful generic straight-stock kg/m.

Can I enter NPS or DN as outside diameter?

No. Use the dimensional standard or supplier drawing to find actual OD. The schedule table tool supplies a few explicitly sourced pipe examples.

Is wall thickness equal to a schedule number?

No. Schedule 10S or 40S is a series whose wall depends on nominal size. Enter the actual decimal thickness, or use a sourced preset.

Can I export this calculation to Excel?

Calculate first, then choose Export CSV. The CSV contains the submitted model and inputs plus piece mass, total mass and applicable unit weights. Excel can open this text format; it is not a downloadable formula workbook or desktop application.

Does optional price include shipping or fabrication?

No. Enter a price per kg or per lb in the chosen currency label. The total is material mass times that unit price only, with no exchange-rate lookup, tax, minimum order, cutting loss or fabrication labor.

How should I read the calculated tables?

Each table states its geometry, material density and assumptions. Example dimensions are calculation scenarios unless explicitly identified as sourced nominal presets. They are not an inventory list or tolerance guarantee.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, certified tolerances or proprietary performance ratings.

  • OpenStax College Physics 2e, 11.2 Density: mass, volume and density relationshiphttps://openstax.org/books/college-physics-2e/pages/11-2-density
  • NIST SP 811, Appendix B.9: mass, length and derived-unit conversionshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors/nist-guide-si-appendix-b9
  • NIST SRD 71 Users Guide, Table A.3: elemental solids at/near room temperaturehttps://www.nist.gov/system/files/documents/srd/SRD71UsersGuideV1-2.pdf