Metal weight calculators / Copper alloys combinations
Metal by dimension. Mass by calculation.
Brass Tube Weight Calculator
Calculate brass tube weight from actual dimensions, density and quantity. Read kg, lb and applicable unit weights, with an optional material-cost estimate.
Your material & dimensions
Your result
Ready to calculateEnter your values and press Calculate. The result will open on the calculation page.
Published references · Clear assumptions · No sign-up
The method
Formula and calculation steps
ID = OD − 2t; A = π(OD² − ID²)/4; mass = density × A × length.
Calculate brass tube weight from actual dimensions, density and quantity. Read kg, lb and applicable unit weights, with an optional material-cost estimate.
- Select a material reference, shape and a consistent dimension unit.
- Confirm metal density, actual dimensions and whether a nominal source preset applies.
- Submit the form, then interpret the result with the assumptions and limits below.
Straight hollow circular section, positive bore required. No fittings, seam allowance, lining, thread loss or coating unless separately stated. All dimensions are nominal or user supplied; use a scale or certified product data for shipping, billing and final procurement.
Brass Round Tube: dimensions, density and unit-weight formula
Brass starts at 8530 kg/m³. Uses C26000 cartridge brass as a named example. Other brass compositions need a different density. Reference basis: C26000 cartridge brass representative.
Use actual outside diameter and wall thickness. Nominal pipe size is a designation, not a measured outside diameter. Pipe schedules, tube gauge systems and delivered tolerances must be resolved before using dimensional arithmetic.
For brass tube weight, keep a single physical piece definition: separate lengths, product counts and voids before multiplying. Convert dimensions consistently; millimetre volume scales by 10⁻⁹ to m³, while cubic inches use 0.0254³. Nominal designation and measured dimension are different inputs. Verify the drawing or product specification before interpreting a calculated total.
Continue with: Brass Flat Bar Weight Calculator · Brass Hex Bar Weight Calculator · Brass Pipe Weight Calculator · Brass Plate Weight Calculator
Check the numbers
Brass Tube Weight Calculator: calculated examples
These results are calculated from the dimensions or published-mass records stated in each row. They are not a complete inventory, certified tolerance table or structural design.
Worked example with stated inputs
Material density reference = Brass; Shape = Round Tube; Dimension units = Millimetres (mm); Density (editable override) = 8530 kg/m³; Outside / solid diameter = 50 mm; Wall thickness = 3 mm; Piece / sidewall length = 1000 mm; Quantity = 1 pieces; Optional unit price (0 = omit) = 0 ; Price basis = Price per kg; Cost currency label = USD.
| Output | Computed result |
|---|---|
| Single-piece calculated mass | 3.778488 kg |
| Single-piece mass | 8.33014 lb |
| Quantity | 1 pieces |
| Total mass | 3.778488 kg |
| Total mass in pounds | 8.33014 lb |
| Linear mass | 3.778488 kg/m |
| Linear mass in imperial units | 2.539027 lb/ft |
| Net model metal volume | 0.000443 m³ |
| Selected shape | Round Tube |
| Material reference | Brass |
| Density entered | 8,530 kg/m³ |
| Calculation basis | Geometry × supplied density |
Dimensioned weight examples in kg
| Scenario | Dimension set / calculation basis | Result |
|---|---|---|
| 500 mm | Piece / sidewall length | 1.889244 kg |
| 750 mm | Piece / sidewall length | 2.833866 kg |
| 1000 mm | Piece / sidewall length | 3.778488 kg |
| 1500 mm | Piece / sidewall length | 5.667732 kg |
| 2000 mm | Piece / sidewall length | 7.556975 kg |
| 3000 mm | Piece / sidewall length | 11.335463 kg |
Unchanged inputs use: Material density reference = Brass; Shape = Round Tube; Dimension units = Millimetres (mm); Density (editable override) = 8530 kg/m³; Outside / solid diameter = 50 mm; Wall thickness = 3 mm; Piece / sidewall length = 1000 mm; Quantity = 1 pieces; Optional unit price (0 = omit) = 0 ; Price basis = Price per kg; Cost currency label = USD. Results retain the model limitations described above.
Common questions
What density does this material weight calculator use?
Brass starts at 8530 kg/m³. Uses C26000 cartridge brass as a named example. Other brass compositions need a different density. Reference basis: C26000 cartridge brass representative.
What is the brass tube weight calculation formula?
ID = OD − 2t; A = π(OD² − ID²)/4; mass = density × A × length. The initial density is 8530 kg/m³ for C26000 cartridge brass representative. The dimensioned examples on this page show the resulting piece mass; quantity and optional unit price are applied separately.
How do I calculate weight in kg and lbs?
The dimensional model gives metal volume in m³, multiplied by the entered kg/m³ density. One avoirdupois pound is exactly 0.45359237 kg. The result reports kg and lb; these are mass units, while force weight would require a gravitational acceleration.
Can I get weight per meter and per foot?
Uniform bars, pipes and section-area models report kg/m and lb/ft. One foot is exactly 0.3048 m. Area and nonuniform objects instead use their stated geometry; a sphere or coil does not have a meaningful generic straight-stock kg/m.
Can I enter NPS or DN as outside diameter?
No. Use the dimensional standard or supplier drawing to find actual OD. The schedule table tool supplies a few explicitly sourced pipe examples.
Is wall thickness equal to a schedule number?
No. Schedule 10S or 40S is a series whose wall depends on nominal size. Enter the actual decimal thickness, or use a sourced preset.
Can I export this calculation to Excel?
Calculate first, then choose Export CSV. The CSV contains the submitted model and inputs plus piece mass, total mass and applicable unit weights. Excel can open this text format; it is not a downloadable formula workbook or desktop application.
Does optional price include shipping or fabrication?
No. Enter a price per kg or per lb in the chosen currency label. The total is material mass times that unit price only, with no exchange-rate lookup, tax, minimum order, cutting loss or fabrication labor.
How should I read the calculated tables?
Each table states its geometry, material density and assumptions. Example dimensions are calculation scenarios unless explicitly identified as sourced nominal presets. They are not an inventory list or tolerance guarantee.
Related calculators
Formula sources and references
References support the underlying methods and units. Chosen example inputs are not universal recommendations, certified tolerances or proprietary performance ratings.
- OpenStax College Physics 2e, 11.2 Density: mass, volume and density relationshiphttps://openstax.org/books/college-physics-2e/pages/11-2-density
- NIST SP 811, Appendix B.9: mass, length and derived-unit conversionshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors/nist-guide-si-appendix-b9
- Copper Development Association: architectural alloys, C26000 densityhttps://copper.org/publications/pub_list/pdf/A4039-ArchitecturalApplications.pdf