Metal Weight CalculatorMaterials, shapes & unit weights

Metal weight calculators / Copper alloys combinations

Metal by dimension. Mass by calculation.

Bronze Tube Weight Calculator

Calculate bronze tube weight from actual dimensions, density and quantity. Read kg, lb and applicable unit weights, with an optional material-cost estimate.

Your material & dimensions

kg/m³
mm
mm
mm
pieces

Preset densities are editable reference estimates. Dimensions use the selected mm/in unit. Published kg/m presets use their source mass directly; choose Custom dimensions to edit their geometry. Initial inputs are examples.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

ID = OD − 2t; A = π(OD² − ID²)/4; mass = density × A × length.

Calculate bronze tube weight from actual dimensions, density and quantity. Read kg, lb and applicable unit weights, with an optional material-cost estimate.

  1. Select a material reference, shape and a consistent dimension unit.
  2. Confirm metal density, actual dimensions and whether a nominal source preset applies.
  3. Submit the form, then interpret the result with the assumptions and limits below.

Straight hollow circular section, positive bore required. No fittings, seam allowance, lining, thread loss or coating unless separately stated. All dimensions are nominal or user supplied; use a scale or certified product data for shipping, billing and final procurement.

Bronze Round Tube: dimensions, density and unit-weight formula

Bronze starts at 8800 kg/m³. Uses C93200 bearing bronze as a named example, not a density for every tin, silicon or aluminium bronze. Reference basis: C93200 bearing bronze representative.

Use actual outside diameter and wall thickness. Nominal pipe size is a designation, not a measured outside diameter. Pipe schedules, tube gauge systems and delivered tolerances must be resolved before using dimensional arithmetic.

For bronze tube weight, keep a single physical piece definition: separate lengths, product counts and voids before multiplying. Convert dimensions consistently; millimetre volume scales by 10⁻⁹ to m³, while cubic inches use 0.0254³. Nominal designation and measured dimension are different inputs. Verify the drawing or product specification before interpreting a calculated total.

Check the numbers

Bronze Tube Weight Calculator: calculated examples

These results are calculated from the dimensions or published-mass records stated in each row. They are not a complete inventory, certified tolerance table or structural design.

Worked example with stated inputs

Material density reference = Bronze; Shape = Round Tube; Dimension units = Millimetres (mm); Density (editable override) = 8800 kg/m³; Outside / solid diameter = 50 mm; Wall thickness = 3 mm; Piece / sidewall length = 1000 mm; Quantity = 1 pieces; Optional unit price (0 = omit) = 0 ; Price basis = Price per kg; Cost currency label = USD.

OutputComputed result
Single-piece calculated mass3.898088 kg
Single-piece mass8.593813 lb
Quantity1 pieces
Total mass3.898088 kg
Total mass in pounds8.593813 lb
Linear mass3.898088 kg/m
Linear mass in imperial units2.619394 lb/ft
Net model metal volume0.000443 m³
Selected shapeRound Tube
Material referenceBronze
Density entered8,800 kg/m³
Calculation basisGeometry × supplied density

Dimensioned weight examples in kg

ScenarioDimension set / calculation basisResult
500 mmPiece / sidewall length1.949044 kg
750 mmPiece / sidewall length2.923566 kg
1000 mmPiece / sidewall length3.898088 kg
1500 mmPiece / sidewall length5.847132 kg
2000 mmPiece / sidewall length7.796176 kg
3000 mmPiece / sidewall length11.694264 kg

Unchanged inputs use: Material density reference = Bronze; Shape = Round Tube; Dimension units = Millimetres (mm); Density (editable override) = 8800 kg/m³; Outside / solid diameter = 50 mm; Wall thickness = 3 mm; Piece / sidewall length = 1000 mm; Quantity = 1 pieces; Optional unit price (0 = omit) = 0 ; Price basis = Price per kg; Cost currency label = USD. Results retain the model limitations described above.

Common questions

What density does this material weight calculator use?

Bronze starts at 8800 kg/m³. Uses C93200 bearing bronze as a named example, not a density for every tin, silicon or aluminium bronze. Reference basis: C93200 bearing bronze representative.

What is the bronze tube weight calculation formula?

ID = OD − 2t; A = π(OD² − ID²)/4; mass = density × A × length. The initial density is 8800 kg/m³ for C93200 bearing bronze representative. The dimensioned examples on this page show the resulting piece mass; quantity and optional unit price are applied separately.

How do I calculate weight in kg and lbs?

The dimensional model gives metal volume in m³, multiplied by the entered kg/m³ density. One avoirdupois pound is exactly 0.45359237 kg. The result reports kg and lb; these are mass units, while force weight would require a gravitational acceleration.

Can I get weight per meter and per foot?

Uniform bars, pipes and section-area models report kg/m and lb/ft. One foot is exactly 0.3048 m. Area and nonuniform objects instead use their stated geometry; a sphere or coil does not have a meaningful generic straight-stock kg/m.

Can I enter NPS or DN as outside diameter?

No. Use the dimensional standard or supplier drawing to find actual OD. The schedule table tool supplies a few explicitly sourced pipe examples.

Is wall thickness equal to a schedule number?

No. Schedule 10S or 40S is a series whose wall depends on nominal size. Enter the actual decimal thickness, or use a sourced preset.

Can I export this calculation to Excel?

Calculate first, then choose Export CSV. The CSV contains the submitted model and inputs plus piece mass, total mass and applicable unit weights. Excel can open this text format; it is not a downloadable formula workbook or desktop application.

Does optional price include shipping or fabrication?

No. Enter a price per kg or per lb in the chosen currency label. The total is material mass times that unit price only, with no exchange-rate lookup, tax, minimum order, cutting loss or fabrication labor.

How should I read the calculated tables?

Each table states its geometry, material density and assumptions. Example dimensions are calculation scenarios unless explicitly identified as sourced nominal presets. They are not an inventory list or tolerance guarantee.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, certified tolerances or proprietary performance ratings.

  • OpenStax College Physics 2e, 11.2 Density: mass, volume and density relationshiphttps://openstax.org/books/college-physics-2e/pages/11-2-density
  • NIST SP 811, Appendix B.9: mass, length and derived-unit conversionshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors/nist-guide-si-appendix-b9
  • Copper Development Association: cast copper alloy sleeve bearings, density tablehttps://www.copper.org/publications/pub_list/pdf/sleevebearing_a1063_06.pdf