Metal Weight CalculatorMaterials, shapes & unit weights

Metal weight calculators / Steel combinations

Metal by dimension. Mass by calculation.

MS I Beam Weight Calculator

Calculate ms i beam weight from actual dimensions, density and quantity. Read kg, lb and applicable unit weights, with an optional material-cost estimate.

Your material & dimensions

kg/m³
mm
mm
mm
mm
mm
pieces

Preset densities are editable reference estimates. Dimensions use the selected mm/in unit. Published kg/m presets use their source mass directly; choose Custom dimensions to edit their geometry. Initial inputs are examples.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

I/channel: A = 2Btf + (H−2tf)tw; T: A = Btf + (H−tf)tw; mass = density × A × length.

Calculate ms i beam weight from actual dimensions, density and quantity. Read kg, lb and applicable unit weights, with an optional material-cost estimate.

  1. Select a material reference, shape and a consistent dimension unit.
  2. Confirm metal density, actual dimensions and whether a nominal source preset applies.
  3. Submit the form, then interpret the result with the assumptions and limits below.

Sharp-corner fabricated section; excludes rolled fillets, tapered flanges and catalogue tolerances. W, UB, ISMB and ISMC nominal masses require their dedicated source records. All dimensions are nominal or user supplied; use a scale or certified product data for shipping, billing and final procurement.

Mild Steel (MS) I / H Beam: dimensions, density and unit-weight formula

Mild Steel (MS) starts at 7850 kg/m³. MS means mild steel, not stainless steel. This structural-steel estimate does not certify a particular mild-steel product. Reference basis: Representative structural steel.

The flange and web rectangles are partitioned without overlap. I and channel sections can share a geometric area even though their centroids and structural behavior differ. This calculator concerns mass only and does not compute bending strength, buckling or safe load.

For ms i beam weight, keep a single physical piece definition: separate lengths, product counts and voids before multiplying. Convert dimensions consistently; millimetre volume scales by 10⁻⁹ to m³, while cubic inches use 0.0254³. Nominal designation and measured dimension are different inputs. Verify the drawing or product specification before interpreting a calculated total.

Check the numbers

MS I Beam Weight Calculator: calculated examples

These results are calculated from the dimensions or published-mass records stated in each row. They are not a complete inventory, certified tolerance table or structural design.

Worked example with stated inputs

Material density reference = Mild Steel (MS); Shape = I / H Beam; Dimension units = Millimetres (mm); Density (editable override) = 7850 kg/m³; Dimension / published-mass preset = Custom dimensions; Overall section depth = 200 mm; Flange width = 100 mm; Web thickness = 6 mm; Flange thickness = 10 mm; Piece / sidewall length = 1000 mm; Quantity = 1 pieces; Optional unit price (0 = omit) = 0 ; Price basis = Price per kg; Cost currency label = USD.

OutputComputed result
Single-piece calculated mass24.178 kg
Single-piece mass53.303366 lb
Quantity1 pieces
Total mass24.178 kg
Total mass in pounds53.303366 lb
Linear mass24.178 kg/m
Linear mass in imperial units16.246866 lb/ft
Net model metal volume0.00308 m³
Selected shapeI / H Beam
Material referenceMild Steel (MS)
Density entered7,850 kg/m³
Calculation basisGeometry × supplied density

Dimensioned weight examples in kg

ScenarioDimension set / calculation basisResult
ISMB 100 x 50Published nominal kg/m × 1 m8.95 kg
ISMB 150 x 75Published nominal kg/m × 1 m14.96 kg
ISMB 200 x 100Published nominal kg/m × 1 m24.17 kg

Unchanged inputs use: Material density reference = Mild Steel (MS); Shape = I / H Beam; Dimension units = Millimetres (mm); Density (editable override) = 7850 kg/m³; Dimension / published-mass preset = Custom dimensions; Overall section depth = 200 mm; Flange width = 100 mm; Web thickness = 6 mm; Flange thickness = 10 mm; Piece / sidewall length = 1000 mm; Quantity = 1 pieces; Optional unit price (0 = omit) = 0 ; Price basis = Price per kg; Cost currency label = USD. Results retain the model limitations described above.

Common questions

What density does this material weight calculator use?

Mild Steel (MS) starts at 7850 kg/m³. MS means mild steel, not stainless steel. This structural-steel estimate does not certify a particular mild-steel product. Reference basis: Representative structural steel.

What is the ms i beam weight calculation formula?

I/channel: A = 2Btf + (H−2tf)tw; T: A = Btf + (H−tf)tw; mass = density × A × length. The initial density is 7850 kg/m³ for Representative structural steel. The dimensioned examples on this page show the resulting piece mass; quantity and optional unit price are applied separately.

How do I calculate weight in kg and lbs?

The dimensional model gives metal volume in m³, multiplied by the entered kg/m³ density. One avoirdupois pound is exactly 0.45359237 kg. The result reports kg and lb; these are mass units, while force weight would require a gravitational acceleration.

Can I get weight per meter and per foot?

Uniform bars, pipes and section-area models report kg/m and lb/ft. One foot is exactly 0.3048 m. Area and nonuniform objects instead use their stated geometry; a sphere or coil does not have a meaningful generic straight-stock kg/m.

Is this an I-beam load calculator?

No. Equal mass does not imply equal strength or stiffness. No span, restraint, load combination or material strength check is performed.

How are the sourced size presets different from custom geometry?

A dimensional preset supplies published nominal OD and wall. A published-mass preset uses its source kg/m directly and ignores density for that mass. Select Custom dimensions for the simple geometric estimate. These two bases can differ because of fillets, manufacturing conventions and catalogue rounding.

Can I use it for rolled standard sections?

Use the catalogue-area or nominal-mass tools for those. Simplified flange and web rectangles omit fillets and may not match a standard chart.

Can I export this calculation to Excel?

Calculate first, then choose Export CSV. The CSV contains the submitted model and inputs plus piece mass, total mass and applicable unit weights. Excel can open this text format; it is not a downloadable formula workbook or desktop application.

Does optional price include shipping or fabrication?

No. Enter a price per kg or per lb in the chosen currency label. The total is material mass times that unit price only, with no exchange-rate lookup, tax, minimum order, cutting loss or fabrication labor.

How should I read the calculated tables?

Each table states its geometry, material density and assumptions. Example dimensions are calculation scenarios unless explicitly identified as sourced nominal presets. They are not an inventory list or tolerance guarantee.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, certified tolerances or proprietary performance ratings.

  • OpenStax College Physics 2e, 11.2 Density: mass, volume and density relationshiphttps://openstax.org/books/college-physics-2e/pages/11-2-density
  • NIST SP 811, Appendix B.9: mass, length and derived-unit conversionshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors/nist-guide-si-appendix-b9
  • SSAB structural hollow sections EPD: steel densityhttps://websitecdn.ssab.com/-/media/Files/EN/Support/Certificates/Hollow-Sections/Environmental-product-declaration---EN-EPD-SSAB-tubes-sections-piles.pdf
  • SAIL: Structurals from SAIL, Product Range; Printed page 9: Conventional Structurals, ISMB, ISMC and ISAhttps://www.sail.co.in/sites/default/files/product-brochure/2023-10/PFS-Brochure_New-2023.pdf
  • Bureau of Indian Standards: IS 808:2021 scope summary; IS 808:2021 Hot Rolled Steel Beam, Column, Channel and Angle Sections — Dimensions and Propertieshttps://www.services.bis.gov.in/tmp/tbl5_2024-11-11-05-24.pdf