Metal weight calculators / Steel combinations
Metal by dimension. Mass by calculation.
MS Ring Weight Calculator
Calculate ms ring weight from actual dimensions, density and quantity. Read kg, lb and applicable unit weights, with an optional material-cost estimate.
Your material & dimensions
Your result
Ready to calculateEnter your values and press Calculate. The result will open on the calculation page.
Published references · Clear assumptions · No sign-up
The method
Formula and calculation steps
V = π(OD²−ID²)t/4 − hole count × πdh²t/4; a disc uses ID=0 and no holes.
Calculate ms ring weight from actual dimensions, density and quantity. Read kg, lb and applicable unit weights, with an optional material-cost estimate.
- Select a material reference, shape and a consistent dimension unit.
- Confirm metal density, actual dimensions and whether a nominal source preset applies.
- Submit the form, then interpret the result with the assumptions and limits below.
Flat blank only. Hole positions must not overlap each other or the bore/edge; a positive remaining volume does not prove a valid bolt layout. All dimensions are nominal or user supplied; use a scale or certified product data for shipping, billing and final procurement.
Mild Steel (MS) Ring: dimensions, density and unit-weight formula
Mild Steel (MS) starts at 7850 kg/m³. MS means mild steel, not stainless steel. This structural-steel estimate does not certify a particular mild-steel product. Reference basis: Representative structural steel.
A ring or flat flange blank is an annular plate. Axial thickness differs from a pipe wall thickness. The optional flange holes remove ideal cylindrical volumes; this does not identify a pressure-class flange or include its hub and facing.
For ms ring weight, keep a single physical piece definition: separate lengths, product counts and voids before multiplying. Convert dimensions consistently; millimetre volume scales by 10⁻⁹ to m³, while cubic inches use 0.0254³. Nominal designation and measured dimension are different inputs. Verify the drawing or product specification before interpreting a calculated total.
Continue with: A36 Steel Plate Weight Calculator · Alloy Steel Pipe Weight Calculator · Alloy Steel Volume Weight Calculator · Carbon Steel Angle Weight Calculator
Check the numbers
MS Ring Weight Calculator: calculated examples
These results are calculated from the dimensions or published-mass records stated in each row. They are not a complete inventory, certified tolerance table or structural design.
Worked example with stated inputs
Material density reference = Mild Steel (MS); Shape = Ring; Dimension units = Millimetres (mm); Density (editable override) = 7850 kg/m³; Outside diameter = 200 mm; Axial thickness = 10 mm; Inside bore diameter = 100 mm; Quantity = 1 pieces; Optional unit price (0 = omit) = 0 ; Price basis = Price per kg; Cost currency label = USD.
| Output | Computed result |
|---|---|
| Single-piece calculated mass | 1.849613 kg |
| Single-piece mass | 4.077698 lb |
| Quantity | 1 pieces |
| Total mass | 1.849613 kg |
| Total mass in pounds | 4.077698 lb |
| Net model metal volume | 0.000236 m³ |
| Selected shape | Ring |
| Material reference | Mild Steel (MS) |
| Density entered | 7,850 kg/m³ |
| Calculation basis | Geometry × supplied density |
Dimensioned weight examples in kg
| Scenario | Dimension set / calculation basis | Result |
|---|---|---|
| 5 mm | Axial thickness | 0.924806 kg |
| 7.5 mm | Axial thickness | 1.38721 kg |
| 10 mm | Axial thickness | 1.849613 kg |
| 15 mm | Axial thickness | 2.774419 kg |
| 20 mm | Axial thickness | 3.699225 kg |
| 30 mm | Axial thickness | 5.548838 kg |
Unchanged inputs use: Material density reference = Mild Steel (MS); Shape = Ring; Dimension units = Millimetres (mm); Density (editable override) = 7850 kg/m³; Outside diameter = 200 mm; Axial thickness = 10 mm; Inside bore diameter = 100 mm; Quantity = 1 pieces; Optional unit price (0 = omit) = 0 ; Price basis = Price per kg; Cost currency label = USD. Results retain the model limitations described above.
Common questions
What density does this material weight calculator use?
Mild Steel (MS) starts at 7850 kg/m³. MS means mild steel, not stainless steel. This structural-steel estimate does not certify a particular mild-steel product. Reference basis: Representative structural steel.
What is the ms ring weight calculation formula?
V = π(OD²−ID²)t/4 − hole count × πdh²t/4; a disc uses ID=0 and no holes. The initial density is 7850 kg/m³ for Representative structural steel. The dimensioned examples on this page show the resulting piece mass; quantity and optional unit price are applied separately.
How do I calculate weight in kg and lbs?
The dimensional model gives metal volume in m³, multiplied by the entered kg/m³ density. One avoirdupois pound is exactly 0.45359237 kg. The result reports kg and lb; these are mass units, while force weight would require a gravitational acceleration.
Can I get weight per meter and per foot?
Uniform bars, pipes and section-area models report kg/m and lb/ft. One foot is exactly 0.3048 m. Area and nonuniform objects instead use their stated geometry; a sphere or coil does not have a meaningful generic straight-stock kg/m.
Does this calculate an ASME pressure-class flange?
No. A finished flange can have a hub, neck, raised face and recesses. Use a detailed drawing or supplier mass for the finished part.
Can this include drilled holes?
The flange blank mode subtracts the supplied through-hole count and diameter. It does not validate bolt-circle spacing or edge distances.
Can I export this calculation to Excel?
Calculate first, then choose Export CSV. The CSV contains the submitted model and inputs plus piece mass, total mass and applicable unit weights. Excel can open this text format; it is not a downloadable formula workbook or desktop application.
Does optional price include shipping or fabrication?
No. Enter a price per kg or per lb in the chosen currency label. The total is material mass times that unit price only, with no exchange-rate lookup, tax, minimum order, cutting loss or fabrication labor.
How should I read the calculated tables?
Each table states its geometry, material density and assumptions. Example dimensions are calculation scenarios unless explicitly identified as sourced nominal presets. They are not an inventory list or tolerance guarantee.
Related calculators
Formula sources and references
References support the underlying methods and units. Chosen example inputs are not universal recommendations, certified tolerances or proprietary performance ratings.
- OpenStax College Physics 2e, 11.2 Density: mass, volume and density relationshiphttps://openstax.org/books/college-physics-2e/pages/11-2-density
- NIST SP 811, Appendix B.9: mass, length and derived-unit conversionshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors/nist-guide-si-appendix-b9
- SSAB structural hollow sections EPD: steel densityhttps://websitecdn.ssab.com/-/media/Files/EN/Support/Certificates/Hollow-Sections/Environmental-product-declaration---EN-EPD-SSAB-tubes-sections-piles.pdf