Metal weight calculators / Steel combinations
Metal by dimension. Mass by calculation.
Steel Wire Mesh Weight Calculator
Calculate steel wire mesh weight from actual dimensions, density and quantity. Read kg, lb and applicable unit weights, with an optional material-cost estimate.
Your material & dimensions
Your result
Ready to calculateEnter your values and press Calculate. The result will open on the calculation page.
Published references · Clear assumptions · No sign-up
The method
Formula and calculation steps
nwidth = floor(width/pitch)+1; nlength = floor(length/pitch)+1; wire volume = πd²/4 × (nwidth×length+nlength×width) × length factor.
Calculate steel wire mesh weight from actual dimensions, density and quantity. Read kg, lb and applicable unit weights, with an optional material-cost estimate.
- Select a material reference, shape and a consistent dimension unit.
- Confirm metal density, actual dimensions and whether a nominal source preset applies.
- Submit the form, then interpret the result with the assumptions and limits below.
Explicit square wire-grid model; not expanded metal, perforated sheet, chain link or gabion fittings. All dimensions are nominal or user supplied; use a scale or certified product data for shipping, billing and final procurement.
Steel Welded / Woven Wire Mesh: dimensions, density and unit-weight formula
Steel starts at 7850 kg/m³. A conventional structural-steel estimate. Select the actual alloy or enter certified density when known. Reference basis: Representative structural steel.
The panel has a square grid with wires on both boundary edges according to the integer-count convention. Pitch is centre-to-centre spacing, not the clear aperture. A measured length factor can account for crimp; welded straight wires normally use a stated value near one.
For steel wire mesh weight, keep a single physical piece definition: separate lengths, product counts and voids before multiplying. Convert dimensions consistently; millimetre volume scales by 10⁻⁹ to m³, while cubic inches use 0.0254³. Nominal designation and measured dimension are different inputs. Verify the drawing or product specification before interpreting a calculated total.
Continue with: A36 Steel Plate Weight Calculator · Alloy Steel Pipe Weight Calculator · Alloy Steel Volume Weight Calculator · Carbon Steel Angle Weight Calculator
Check the numbers
Steel Wire Mesh Weight Calculator: calculated examples
These results are calculated from the dimensions or published-mass records stated in each row. They are not a complete inventory, certified tolerance table or structural design.
Worked example with stated inputs
Material density reference = Steel; Shape = Welded / Woven Wire Mesh; Dimension units = Millimetres (mm); Density (editable override) = 7850 kg/m³; Width = 1000 mm; Piece / sidewall length = 1000 mm; Metal wire diameter = 3 mm; Wire centre-to-centre pitch = 25 mm; Wire length factor = 1 ratio; Quantity = 1 pieces; Optional unit price (0 = omit) = 0 ; Price basis = Price per kg; Cost currency label = USD.
| Output | Computed result |
|---|---|
| Single-piece calculated mass | 4.550047 kg |
| Single-piece mass | 10.031137 lb |
| Quantity | 1 pieces |
| Total mass | 4.550047 kg |
| Total mass in pounds | 10.031137 lb |
| Projected area mass | 4.550047 kg/m² |
| Projected area mass in imperial units | 0.931923 lb/ft² |
| Net model metal volume | 0.00058 m³ |
| Selected shape | Welded / Woven Wire Mesh |
| Material reference | Steel |
| Density entered | 7,850 kg/m³ |
| Calculation basis | Geometry × supplied density |
Dimensioned weight examples in kg
| Scenario | Dimension set / calculation basis | Result |
|---|---|---|
| 500 mm | Piece / sidewall length | 2.302768 kg |
| 750 mm | Piece / sidewall length | 3.426407 kg |
| 1000 mm | Piece / sidewall length | 4.550047 kg |
| 1500 mm | Piece / sidewall length | 6.797327 kg |
| 2000 mm | Piece / sidewall length | 9.044606 kg |
| 3000 mm | Piece / sidewall length | 13.539165 kg |
Unchanged inputs use: Material density reference = Steel; Shape = Welded / Woven Wire Mesh; Dimension units = Millimetres (mm); Density (editable override) = 7850 kg/m³; Width = 1000 mm; Piece / sidewall length = 1000 mm; Metal wire diameter = 3 mm; Wire centre-to-centre pitch = 25 mm; Wire length factor = 1 ratio; Quantity = 1 pieces; Optional unit price (0 = omit) = 0 ; Price basis = Price per kg; Cost currency label = USD. Results retain the model limitations described above.
Common questions
What density does this material weight calculator use?
Steel starts at 7850 kg/m³. A conventional structural-steel estimate. Select the actual alloy or enter certified density when known. Reference basis: Representative structural steel.
What is the steel wire mesh weight calculation formula?
nwidth = floor(width/pitch)+1; nlength = floor(length/pitch)+1; wire volume = πd²/4 × (nwidth×length+nlength×width) × length factor. The initial density is 7850 kg/m³ for Representative structural steel. The dimensioned examples on this page show the resulting piece mass; quantity and optional unit price are applied separately.
How do I calculate weight in kg and lbs?
The dimensional model gives metal volume in m³, multiplied by the entered kg/m³ density. One avoirdupois pound is exactly 0.45359237 kg. The result reports kg and lb; these are mass units, while force weight would require a gravitational acceleration.
Can I get weight per meter and per foot?
Uniform bars, pipes and section-area models report kg/m and lb/ft. One foot is exactly 0.3048 m. Area and nonuniform objects instead use their stated geometry; a sphere or coil does not have a meaningful generic straight-stock kg/m.
Is aperture the same as pitch?
No. For equal round wires, centre-to-centre pitch is approximately clear aperture plus wire diameter.
Why can small width changes add a step in mass?
Wire counts are integers. Crossing a full-pitch boundary adds a wire under the stated edge convention.
Can I export this calculation to Excel?
Calculate first, then choose Export CSV. The CSV contains the submitted model and inputs plus piece mass, total mass and applicable unit weights. Excel can open this text format; it is not a downloadable formula workbook or desktop application.
Does optional price include shipping or fabrication?
No. Enter a price per kg or per lb in the chosen currency label. The total is material mass times that unit price only, with no exchange-rate lookup, tax, minimum order, cutting loss or fabrication labor.
How should I read the calculated tables?
Each table states its geometry, material density and assumptions. Example dimensions are calculation scenarios unless explicitly identified as sourced nominal presets. They are not an inventory list or tolerance guarantee.
Related calculators
Formula sources and references
References support the underlying methods and units. Chosen example inputs are not universal recommendations, certified tolerances or proprietary performance ratings.
- OpenStax College Physics 2e, 11.2 Density: mass, volume and density relationshiphttps://openstax.org/books/college-physics-2e/pages/11-2-density
- NIST SP 811, Appendix B.9: mass, length and derived-unit conversionshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors/nist-guide-si-appendix-b9
- SSAB structural hollow sections EPD: steel densityhttps://websitecdn.ssab.com/-/media/Files/EN/Support/Certificates/Hollow-Sections/Environmental-product-declaration---EN-EPD-SSAB-tubes-sections-piles.pdf