Metal weight calculators / Other metals combinations
Metal by dimension. Mass by calculation.
Titanium Round Bar Weight Calculator
Calculate titanium round bar weight from actual dimensions, density and quantity. Read kg, lb and applicable unit weights, with an optional material-cost estimate.
Your material & dimensions
Your result
Ready to calculateEnter your values and press Calculate. The result will open on the calculation page.
Published references · Clear assumptions · No sign-up
The method
Formula and calculation steps
A = πd²/4; mass = density × A × length.
Calculate titanium round bar weight from actual dimensions, density and quantity. Read kg, lb and applicable unit weights, with an optional material-cost estimate.
- Select a material reference, shape and a consistent dimension unit.
- Confirm metal density, actual dimensions and whether a nominal source preset applies.
- Submit the form, then interpret the result with the assumptions and limits below.
Uniform solid circular section. Rebar uses nominal equivalent diameter; ribs, bundled strands, insulation and coatings are not measured by this model. All dimensions are nominal or user supplied; use a scale or certified product data for shipping, billing and final procurement.
Titanium Round Bar: dimensions, density and unit-weight formula
Titanium starts at 4506 kg/m³. Elemental titanium reference. Ti-6Al-4V and other titanium alloys require their own density. Reference basis: Elemental titanium at/near room temperature.
The diameter is the metal section diameter rather than an insulated cable diameter. The circular-area relationship means doubling diameter multiplies nominal unit weight by four while doubling length multiplies piece weight by two.
For titanium round bar weight, keep a single physical piece definition: separate lengths, product counts and voids before multiplying. Convert dimensions consistently; millimetre volume scales by 10⁻⁹ to m³, while cubic inches use 0.0254³. Nominal designation and measured dimension are different inputs. Verify the drawing or product specification before interpreting a calculated total.
Continue with: Lead Sheet Weight Calculator · Lead Sphere Weight Calculator · Lead Volume Weight Calculator · Magnesium Plate Weight Calculator
Check the numbers
Titanium Round Bar Weight Calculator: calculated examples
These results are calculated from the dimensions or published-mass records stated in each row. They are not a complete inventory, certified tolerance table or structural design.
Worked example with stated inputs
Material density reference = Titanium; Shape = Round Bar; Dimension units = Millimetres (mm); Density (editable override) = 4506 kg/m³; Outside / solid diameter = 50 mm; Piece / sidewall length = 1000 mm; Quantity = 1 pieces; Optional unit price (0 = omit) = 0 ; Price basis = Price per kg; Cost currency label = USD.
| Output | Computed result |
|---|---|
| Single-piece calculated mass | 8.84751 kg |
| Single-piece mass | 19.505421 lb |
| Quantity | 1 pieces |
| Total mass | 8.84751 kg |
| Total mass in pounds | 19.505421 lb |
| Linear mass | 8.84751 kg/m |
| Linear mass in imperial units | 5.945252 lb/ft |
| Net model metal volume | 0.001963 m³ |
| Selected shape | Round Bar |
| Material reference | Titanium |
| Density entered | 4,506 kg/m³ |
| Calculation basis | Geometry × supplied density |
Dimensioned weight examples in kg
| Scenario | Dimension set / calculation basis | Result |
|---|---|---|
| 500 mm | Piece / sidewall length | 4.423755 kg |
| 750 mm | Piece / sidewall length | 6.635633 kg |
| 1000 mm | Piece / sidewall length | 8.84751 kg |
| 1500 mm | Piece / sidewall length | 13.271265 kg |
| 2000 mm | Piece / sidewall length | 17.695021 kg |
| 3000 mm | Piece / sidewall length | 26.542531 kg |
Unchanged inputs use: Material density reference = Titanium; Shape = Round Bar; Dimension units = Millimetres (mm); Density (editable override) = 4506 kg/m³; Outside / solid diameter = 50 mm; Piece / sidewall length = 1000 mm; Quantity = 1 pieces; Optional unit price (0 = omit) = 0 ; Price basis = Price per kg; Cost currency label = USD. Results retain the model limitations described above.
Common questions
What density does this material weight calculator use?
Titanium starts at 4506 kg/m³. Elemental titanium reference. Ti-6Al-4V and other titanium alloys require their own density. Reference basis: Elemental titanium at/near room temperature.
What is the titanium round bar weight calculation formula?
A = πd²/4; mass = density × A × length. The initial density is 4506 kg/m³ for Elemental titanium at/near room temperature. The dimensioned examples on this page show the resulting piece mass; quantity and optional unit price are applied separately.
How do I calculate weight in kg and lbs?
The dimensional model gives metal volume in m³, multiplied by the entered kg/m³ density. One avoirdupois pound is exactly 0.45359237 kg. The result reports kg and lb; these are mass units, while force weight would require a gravitational acceleration.
Can I get weight per meter and per foot?
Uniform bars, pipes and section-area models report kg/m and lb/ft. One foot is exactly 0.3048 m. Area and nonuniform objects instead use their stated geometry; a sphere or coil does not have a meaningful generic straight-stock kg/m.
How is the D²/162 rebar formula derived?
With steel density 7850 kg/m³ and diameter D in mm, kg/m = 0.0061653756 D², approximately D²/162.2. D²/162 is a rounded field shortcut, not a universal grade or standard tolerance.
Can I use the outside size of stranded cable?
No. Use the sum of metallic conductor areas in the cross-section-area tool. Insulation, voids and lay length need their own treatment.
Can I export this calculation to Excel?
Calculate first, then choose Export CSV. The CSV contains the submitted model and inputs plus piece mass, total mass and applicable unit weights. Excel can open this text format; it is not a downloadable formula workbook or desktop application.
Does optional price include shipping or fabrication?
No. Enter a price per kg or per lb in the chosen currency label. The total is material mass times that unit price only, with no exchange-rate lookup, tax, minimum order, cutting loss or fabrication labor.
How should I read the calculated tables?
Each table states its geometry, material density and assumptions. Example dimensions are calculation scenarios unless explicitly identified as sourced nominal presets. They are not an inventory list or tolerance guarantee.
Related calculators
Formula sources and references
References support the underlying methods and units. Chosen example inputs are not universal recommendations, certified tolerances or proprietary performance ratings.
- OpenStax College Physics 2e, 11.2 Density: mass, volume and density relationshiphttps://openstax.org/books/college-physics-2e/pages/11-2-density
- NIST SP 811, Appendix B.9: mass, length and derived-unit conversionshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors/nist-guide-si-appendix-b9
- NIST SRD 71 Users Guide, Table A.3: elemental solids at/near room temperaturehttps://www.nist.gov/system/files/documents/srd/SRD71UsersGuideV1-2.pdf