Metal Weight CalculatorMaterials, shapes & unit weights

Metal weight calculators / Coated steel combinations

Metal by dimension. Mass by calculation.

GI Wire Mesh Weight Calculator

Calculate gi wire mesh weight from actual dimensions, density and quantity. Read kg, lb and applicable unit weights, with an optional material-cost estimate.

Your material & dimensions

kg/m³
mm
mm
mm
mm
ratio
pieces

Preset densities are editable reference estimates. Dimensions use the selected mm/in unit. Published kg/m presets use their source mass directly; choose Custom dimensions to edit their geometry. Initial inputs are examples.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

nwidth = floor(width/pitch)+1; nlength = floor(length/pitch)+1; wire volume = πd²/4 × (nwidth×length+nlength×width) × length factor.

Calculate gi wire mesh weight from actual dimensions, density and quantity. Read kg, lb and applicable unit weights, with an optional material-cost estimate.

  1. Select a material reference, shape and a consistent dimension unit.
  2. Confirm metal density, actual dimensions and whether a nominal source preset applies.
  3. Submit the form, then interpret the result with the assumptions and limits below.

Explicit square wire-grid model; not expanded metal, perforated sheet, chain link or gabion fittings. All dimensions are nominal or user supplied; use a scale or certified product data for shipping, billing and final procurement.

Galvanized Steel (GI) Welded / Woven Wire Mesh: dimensions, density and unit-weight formula

Galvanized Steel (GI) starts at 7850 kg/m³. This is the steel substrate only. Add coating mass separately; do not treat galvanized steel as a homogeneous metal at one universal density. Reference basis: Steel base; zinc coating excluded.

The panel has a square grid with wires on both boundary edges according to the integer-count convention. Pitch is centre-to-centre spacing, not the clear aperture. A measured length factor can account for crimp; welded straight wires normally use a stated value near one.

For gi wire mesh weight, keep a single physical piece definition: separate lengths, product counts and voids before multiplying. Convert dimensions consistently; millimetre volume scales by 10⁻⁹ to m³, while cubic inches use 0.0254³. Nominal designation and measured dimension are different inputs. Verify the drawing or product specification before interpreting a calculated total.

Check the numbers

GI Wire Mesh Weight Calculator: calculated examples

These results are calculated from the dimensions or published-mass records stated in each row. They are not a complete inventory, certified tolerance table or structural design.

Worked example with stated inputs

Material density reference = Galvanized Steel (GI); Shape = Welded / Woven Wire Mesh; Dimension units = Millimetres (mm); Density (editable override) = 7850 kg/m³; Width = 1000 mm; Piece / sidewall length = 1000 mm; Metal wire diameter = 3 mm; Wire centre-to-centre pitch = 25 mm; Wire length factor = 1 ratio; Quantity = 1 pieces; Optional unit price (0 = omit) = 0 ; Price basis = Price per kg; Cost currency label = USD.

OutputComputed result
Single-piece calculated mass4.550047 kg
Single-piece mass10.031137 lb
Quantity1 pieces
Total mass4.550047 kg
Total mass in pounds10.031137 lb
Projected area mass4.550047 kg/m²
Projected area mass in imperial units0.931923 lb/ft²
Net model metal volume0.00058 m³
Selected shapeWelded / Woven Wire Mesh
Material referenceGalvanized Steel (GI)
Density entered7,850 kg/m³
Calculation basisGeometry × supplied density

Dimensioned weight examples in kg

ScenarioDimension set / calculation basisResult
500 mmPiece / sidewall length2.302768 kg
750 mmPiece / sidewall length3.426407 kg
1000 mmPiece / sidewall length4.550047 kg
1500 mmPiece / sidewall length6.797327 kg
2000 mmPiece / sidewall length9.044606 kg
3000 mmPiece / sidewall length13.539165 kg

Unchanged inputs use: Material density reference = Galvanized Steel (GI); Shape = Welded / Woven Wire Mesh; Dimension units = Millimetres (mm); Density (editable override) = 7850 kg/m³; Width = 1000 mm; Piece / sidewall length = 1000 mm; Metal wire diameter = 3 mm; Wire centre-to-centre pitch = 25 mm; Wire length factor = 1 ratio; Quantity = 1 pieces; Optional unit price (0 = omit) = 0 ; Price basis = Price per kg; Cost currency label = USD. Results retain the model limitations described above.

Common questions

What density does this material weight calculator use?

Galvanized Steel (GI) starts at 7850 kg/m³. This is the steel substrate only. Add coating mass separately; do not treat galvanized steel as a homogeneous metal at one universal density. Reference basis: Steel base; zinc coating excluded.

What is the gi wire mesh weight calculation formula?

nwidth = floor(width/pitch)+1; nlength = floor(length/pitch)+1; wire volume = πd²/4 × (nwidth×length+nlength×width) × length factor. The initial density is 7850 kg/m³ for Steel base; zinc coating excluded. The dimensioned examples on this page show the resulting piece mass; quantity and optional unit price are applied separately.

Does GI density include the zinc coating?

No. The default 7850 kg/m³ describes the steel substrate. GI pipes, wire and sheet may include zinc, lining or other additions. Add a separately verified coating mass or use the finished product’s measured density/mass; no universal coating is assumed.

How do I calculate weight in kg and lbs?

The dimensional model gives metal volume in m³, multiplied by the entered kg/m³ density. One avoirdupois pound is exactly 0.45359237 kg. The result reports kg and lb; these are mass units, while force weight would require a gravitational acceleration.

Can I get weight per meter and per foot?

Uniform bars, pipes and section-area models report kg/m and lb/ft. One foot is exactly 0.3048 m. Area and nonuniform objects instead use their stated geometry; a sphere or coil does not have a meaningful generic straight-stock kg/m.

Is aperture the same as pitch?

No. For equal round wires, centre-to-centre pitch is approximately clear aperture plus wire diameter.

Why can small width changes add a step in mass?

Wire counts are integers. Crossing a full-pitch boundary adds a wire under the stated edge convention.

Can I export this calculation to Excel?

Calculate first, then choose Export CSV. The CSV contains the submitted model and inputs plus piece mass, total mass and applicable unit weights. Excel can open this text format; it is not a downloadable formula workbook or desktop application.

Does optional price include shipping or fabrication?

No. Enter a price per kg or per lb in the chosen currency label. The total is material mass times that unit price only, with no exchange-rate lookup, tax, minimum order, cutting loss or fabrication labor.

How should I read the calculated tables?

Each table states its geometry, material density and assumptions. Example dimensions are calculation scenarios unless explicitly identified as sourced nominal presets. They are not an inventory list or tolerance guarantee.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, certified tolerances or proprietary performance ratings.

  • OpenStax College Physics 2e, 11.2 Density: mass, volume and density relationshiphttps://openstax.org/books/college-physics-2e/pages/11-2-density
  • NIST SP 811, Appendix B.9: mass, length and derived-unit conversionshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors/nist-guide-si-appendix-b9
  • SSAB metal-coated steel sheets EPD: steel substrate and separate zinc coatinghttps://vpp.bastaonline.se/Documents/510965/EPD/EPD-Metal_coated_steel_sheets_and_coils.pdf